Jims

Jims 5813-5 - Stator Adapter Tool - M8

Milwaukee Eight® Stator Adapter Main Bearing Tool When this adapter is used in conjunction with the main bearing tool, or OE tool, the stator can remain attached to the left side case during bearing...

Jims 18526-PG - Tappet - Standard - XL

Big Axle™ Powerglide™ Tappets Micro-finish bore allows a running fit of .0002" Big Axle™ rollers are designed around three working parts The outer wheel/roller has a 27% greater wall size - less...

Jims 732K - Hardware Organizer - Complete Set - M8

Hardware Organizer M8 JIMS has developed a new set of Milwaukee Eight specific hardware index tools to store and organize bolts while parts are disassembled Can be placed on their side to assist in...

Jims 734 - Hardware Organizer - Primary - M8

Hardware Organizer M8 JIMS has developed a new set of Milwaukee Eight specific hardware index tools to store and organize bolts while parts are disassembled Can be placed on their side to assist in...

Jims 733 - Hardware Organizer - Cam - M8

Hardware Organizer M8 JIMS has developed a new set of Milwaukee Eight specific hardware index tools to store and organize bolts while parts are disassembled Can be placed on their side to assist in...

Jims 732 - Hardware Organizer - Topend - M8

Hardware Organizer M8 JIMS has developed a new set of Milwaukee Eight specific hardware index tools to store and organize bolts while parts are disassembled Can be placed on their side to assist in...

Jims 900 - Main Drive Gear/Bearing Remover/Installer - 6-Speed

Harley Davidson Cruise Drive 6-Speed Main Drive Gear and Bearing Remover/Installer Kit Complete kit for servicing the main drive gear or the main bearing on the latest Harley-Davidson­­® 6-speed...

Jims 730 - Piston Tester Jet - M8

Piston Jet Tester Assists engine rebuilder to clear jet of all assembly lubes; verifies psi number the jet switches to "on" and visualizes spray pattern before cases are sealed Helps determine if...

Jims 5506 - Magnetic Tappet Holder - Twin Cam and M8

Magnetic Tappet Holder Never turn the engine over if the tappet will not spin with your fingers after adjustments were made It is very important that the engine is not rotated while pushrods are...

Jims 991 - Case Splitting Tool - M8

Case Splitting Tool for M8 In order to perform any type of lower end service or performance work, it is necessary to split the crankcase into halves Simply install the tool on the primary side of...

Jims 74420-94 - Electronic Speedometer Sensor - '99-'03 FLT

Electronic Speedometer Sensor Top-quality replacement sensor Also works on any aftermarket transmission case with a speedometer sensor hole Includes O-ring, hardware and OEM connector Made in the...

Jims 74437-96 - Electronic Speedometer Sensor - '00-'06 Softail

Electronic Speedometer Sensor Top-quality replacement sensor Also works on any aftermarket transmission case with a speedometer sensor hole Includes O-ring, hardware and OEM connector Made in the...

Jims 95660-85 - Seal Driver - Transmission Main - 5-Speed

Optional Seal Driver Optional drivers used in conjunction with main shaft seal tool allow installation of seals

Jims 96780-32A - Piston Pin Keeper Tool

Piston Pin Keeper Tool This tool will install “Round Circlip” rings in one easy step without distorting ring, for the safest wrist pin retention possible Use to install retaining ring in piston ...

Jims 2246 - Timken® Bearing Race Installer

Timken® Bearing Race Installer Used to install bearing race straight into the left crankcase A must for late-model cases Made in the U.S.A.

Jims 1720 - Main Bearing Remover - 5-Speed

Main Drive Gear Bearing Removal Tool Removes old bearing straight and will not damage the transmission case Can be used without removing transmission from the bike Made in the U.S.A.

Jims 2256 - Gear Seal Installation - Drive - 5-Speed

Driver Handle Use to install main drive gear oil seal to the proper depth with transmission assembled Includes protective sleeve for seal, which can be used to protect main drive gear inner...

Jims 2233 - Tappet Tool - Oil Filter Plug

Tappet Oil Filter Screw Plug Tool Removes oil screen without removing exhaust Used to remove the tappet oil screen plug Made in the U.S.A.

Jims 1001 - Valve Guide Driver - Set

Shouldered Valve Guide Driver Set Three piece set (3/8", 1/32", 5/16") used to remove or install valve guides Designed for guide removal and installation on all models Made in the U.S.A.

Jims 1284 - Holding Tool - Connecting Rod - V-Twin

Rod Holder Tool Holds the rods in place when reaming or honing the wrist pin bushings Made in the USA For most V-Twin and Buell Blast applications.

Jims 2047 - Fork Seal Installer - 41 mm

Fork Seal and Cap Installer Lightly grease to keep from scratching fork tubes Used to install fork and dust seals Made in the U.S.A.

Jims 1169 - Compression Release Guide - Twin Cam

Compression Release Valve Installation Kit Installation kit includes fixture, drill bit, spot face bit and thread-tapping tool Simply drill, spot face, tap and install compression release valves ...

Jims 2260 - Sprocket Lock Tool - Big Twin

Pulley Locker Lock the transmission pulley for removing or installing pulley nut Made in the U.S.A.

Jims 1745 - Bearing Simulator - Big Twin

Timken® Bearing Simulator Designed to allow quick and easy removal and replacement of flywheel assembly in the left-side crankcase when checking rod-to-case, piston-to-flywheel or...