Jims

Jims 910 - Ring - Piston - Compressor Kit

Piston Ring Compressor Set Fine-tooth ratcheting motion will compress the bands in small increments for accurate compression Will not break or damage rings Made in the U.S.A.

Jims 782 - Cylinder Leakdown - 4-Stroke

Dual Gauge Leakdown Tester Tool troubleshoots cylinder leakdown issues such as valve seat issues, bad rings and bad head gasket Hose assembly has both 14 mm and 18 mm spark plug threads Includes...

Jims 938 - Valve Guide Installer - 7 mm

Shoulderless Valve Guide Tool Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A.

Jims 917 - Clip - Pushrod Cover

Pushrod Cover Clip Will install and remove the clip professionally with just one hand in seconds This tool will NOT marr or slip Made in the U.S.A.

Jims 951 - Torque Plate - Twin Cam '99-'17 - Original Equipment

Cylinder Torque Plate Kit Torque plates must be used when boring or honing late-model aluminum cylinders Simulate running stress conditions Come with instructions Made in the U.S.A.

Jims 2240-19 - Adapter - Valve Guide - Pilot - 7 mm

Valve Guide Adapter Adapters are supported by a stand that makes it easy to press valve guides in and out Adapters for working on 7 mm valve guides Made in the U.S.A.

Jims 604 - Alignment Screws - Rocker Box

Rocker Box Alignment Screws Prevents misalignment of cover, compromising of seal and potential rocker interference Made in the U.S.A.

Jims 935 - Inspection Cutter Tool - Oil Filter

Oil Filter Cutter Use to inspect oil filter for any damaging particles that may be trapped in filter Locks down filter for a clean cut around filter base Fits filters up to 5-1/2" diameter Made...

Jims 753 - Flywheel Lock with Tag - Mighty Bite - Blue - Twin Cam

Mighty Bite Flywheel Lock and Tag Locks flywheel in place when performing service work to the connecting rods or pistons with the cylinders off the engine For use on Twin Cam motors with crank...

Jims 916 - Case Support Blocks

Twin Cam "B" Motor Case Support Blocks Aluminum blocks have inserted Delrin® pads that rest against case to prevent marring and to support the case Keeps case level when using bearing pullers to...

Jims 779 - Balancer Retainer Tool

Hydraulic Balancer Retainer Tool Holds hydraulic tensioners in place that keep constant chain tension on counter balancer system Made in the U.S.A.

Jims 1133 - Reamer Valve Guide Tool - 7 mm

7mm Valve Guide Reamer For 7 mm valve guides Harley-Davidson® No. 16461-02 that are used in conjunction with the latest conical (Beehive) valve springs Will also work on equivalent aftermarket 7 mm...

Jims 993 - Inner Camshaft Bearing Tool

Inner Cam Bearing Removal Tool Used to remove inner cam bearing without damaging the crankcase Tool is also designed to keep rollers from falling into the crankcase Comes with instructions Made...

Jims 2049 - Fork Seal Installation Tool - 49 mm

49mm Fork Seal and Dust Shield Installer Installs lower leg 49 mm fork seals squarely into the bore without damaging the seal lip surface Designed for specific Harley-Davidson® models except...

Jims 988 - Valve Spring - Compressor

Valve Spring Compressor Used to remove and replace valve and new-style conical valve spring Requires use of JIMS Valve Spring Compressor Tool Made in the U.S.A.

Jims 974 - Flywheel Holder - Twin Cam

Flywheel Holder This can be used for checking case clearances when building stroker motors or checking valve to valve clearances Can be used to prevent flywheels from turning at the time of...

Jims 966 - Starter Seal Tool

Starter Jackshaft Seal Installer Tool Easily aligns and installs starter jackshaft seal without distorting or damaging seal Seal is located in upper part of inner primary of Big Twins Made in the...

Jims 2312 - Primary Locking Bar Tool

Primary Locking Bar Immobilizes primary drive Allows for tightening with a torque wrench or loosening with a breaker bar Prevents damage to rotor or magnets sometimes caused by air-wrench Made in...

Jims 1672 - Crankshaft Bearing Tool

Crankshaft Bearing Tool Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in the U.S.A.

Jims 963 - Bearing Puller Tool - '03-'17 Twin Cam

Bearing and Race Puller Tool Can also be used to remove Timken® bearing pinion shaft inner bearing race on '57-'07 XL, including all Buells®, and used to remove press-fit transmission gears and...

Jims 956 - Sleeve Kit

Replacement Sleeve Kit Sleeve is several times stronger than stock aluminum case material that standard bearings ride in Replacement sleeve kit for Timken® Case Bearing Tool

Jims 969 - O² Sensor Tool - Socket

O² Sensor Tool Remove and install oxygen sensors on fuel-injected models Socket tool will withstand up to 125 ft.-lbs. of torque Made in the USA

Jims 1075 - Installer - Cylinder Stud

Evolution Cylinder Stud Assembly Tool Assembly tool features a captive hardened ball bearing dimensionally set 1" from top of tool Works on all Evolution Big Twin and XL models Made in the U.S.A.

Jims 995 - Splitter Case - '07-'17 Twin Cam

Case Splitter Tool "Breaks" the case sealant by pushing apart both case halves Uses included hand thread-in pushing screw Flywheels will be pushed from the left case Bolts to primary mounting...