Jims

Jims 1162 - Caliper Piston Remover

Brake Caliper Piston Remover Prevents damage to pistons and cylinders when installing new seals and wipers Holds pistons square in their cylinder bores during removal Designed for front and rear...

Jims 38515-90 - Clutch Spring Compressor

Clutch Spring Compressor Tool For '91-'03 XL applications, compressor nut must be used in conjunction with compressor tool Used to release clutch spring so retainer ring can be easily removed and...

Jims 38515-91 - Nut Clutch Spring Compressor XL

Clutch Spring Compressor Tool For '91-'03 XL applications, compressor nut must be used in conjunction with compressor tool Used to release clutch spring so retainer ring can be easily removed and...

Jims 2045 - Fork Seal Installer - 35 mm

Fork Seal and Cap Installer Lightly grease to keep from scratching fork tubes Used to install fork and dust seals Made in the U.S.A.

Jims 727K - Valves - Compression Release

Manual Compression Release Valves Simply drill and tap (10 mm x 1.0 mm) each cylinder head and thread in the self-sealing release valves Give your starter a hand by installing these in your...

Jims 1288 - Crankshaft Guide - '99-'17 Twin Cam

Crankshaft Guide Spreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel assembly Made in the U.S.A.

Jims 2317 - Primary Locking Bar - 5-Speed

Primary Locking Bar Immobilizes primary drive Allows for tightening with a torque wrench or loosening with a breaker bar Prevents damage to rotor or magnets sometimes caused by air-wrench Made in...

Jims 1710 - Outer Race Snap Ring

Snap Ring Tool Used for removing and installing the Timken® bearing outer race snap ring A must for replacing rings in OEM and aftermarket cases Made in the U.S.A.

Jims 2324 - Sprocket Shaft Installer

Sprocket Shaft Seal Installer Installs sprocket seal to proper depth Use with JIMS® Driver Handle Holds seal perfectly square Made in the U.S.A.

Jims 95760-XL - Camshaft Bearing - Puller - XL

Inner Cam Bearing Removal Tool Used to remove inner cam bearing without damaging the crankcase Tool is also designed to keep rollers from falling into the crankcase Comes with instructions Made...

Jims 1726-2 - Bushing Reamer - Wrist Pin

Wrist Pin Bushing Reaming Tool Some wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications). Used to ream wrist pin bushings to the...

Jims 2318 - Primary Locking Bar - XL

Primary Locking Bar Immobilizes primary drive Allows for tightening with a torque wrench or loosening with a breaker bar Prevents damage to rotor or magnets sometimes caused by air-wrench Made in...

Jims 1034 - Holder - Sprocket Shaft

Sprocket Shaft Holder Used to hold flywheel assembly in vise, with or without left case attached Made in the U.S.A.

Jims 2046 - Fork Seal Installer - 39 mm

Fork Seal and Cap Installer Lightly grease to keep from scratching fork tubes Used to install fork and dust seals Made in the U.S.A.

Jims 1146 - Crankshaft Bearing Installer - Twin Cam

Twin Cam "B" Motor Crankshaft Bearing Tool Designed to protect engine cases by using a specially-designed support block to remove or install cam side crankshaft bearing Made in the U.S.A.

Jims 95660-77 - Seal Driver - 4-Speed - Big Twin

Optional Seal Driver Optional drivers used in conjunction with main shaft seal tool allow installation of seals

Jims 2392 - Head Bolt - Torque Plate

Head Bolt Torque Gauge This accurate gauge allows the measuring of 90° when tightening head bolts Torquing sequence laser engraved on gauge, with instructions Works on all Twin Cam and Evolution...

Jims 1726-1 - Bushing Reamer - Wrist Pin

Wrist Pin Bushing Reaming Tool Some wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications). Used to ream wrist pin bushings to the...

Jims 2043 - Fork Nut Socket - 41 mm

Fork Nut Socket Eliminates possible burring of plug caused by wrenches Used to remove and install top fork-tube plug Fits 41 mm forks Made in the U.S.A.

Jims 2316 - Primary Locking Bar - 4-Speed/5-Speed

Primary Locking Bar Immobilizes primary drive Allows for tightening with a torque wrench or loosening with a breaker bar Prevents damage to rotor or magnets sometimes caused by air-wrench Made in...

Jims 1705 - Exhaust Drill Plate

Exhaust Stud Drill Plate Will position the seal evenly into the exhaust port of head Tool can be used with exhaust flange nuts Made in the U.S.A.

Jims 1709 - Sprocket Shaft Bearing Tool - Big Twin

Sprocket Shaft Bearing Remover Tool is used to remove the sprocket shaft Timken® bearing on late '86-'02 Big Twins with an integral sprocket shaft Does the job better than anything else on the...

Jims 1726-3 - Bushing Reamer - Wrist Pin

Wrist Pin Bushing Reaming Tool Some wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications). Used to ream wrist pin bushings to the...

Jims 33443-84 - Tappet Aligning Tool - Big Twin

Tappet Block Alignment Tool Can also be used to align rocker box bases on Evolution head (requires two tools) Also used in Harley-Davidson® Twin Cam oil pump alignment applications Used to align...