Jims

Jims 1163 - Ball Shaft Retention Pins

Balancer Shaft Retention Pins Lock into balancer shaft sprocket pinholes to prevent balancer from turning out of sync with flywheel Use to secure balancers when servicing the flywheel assembly ...

Jims 1111 - Camshaft Pinion Gauge Pins 108

Cam and Pinion Gear Gauge Pins Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A.

Jims 1167 - Balancing Shaft Bearing Tool

Balancer Shaft Bearing Remover Installing portion is designed to push on the outer diameter of bearings preventing any damage to the bearing or it's bore Pulls the bearings from the "B" motor case...

Jims 1148 - Rod Alignment Tool - Twin Cam

Rod Alignment Tool Use to check rod straightness without removing the rods from the cases Made in the U.S.A.

Jims 97235-55B - Sprocket Shaft Bearing Nut Tool

Sprocket Shaft Bearing Nut Wrench Used to install and remove bearing nut Made in the U.S.A.

Jims 97272-60 - Camshaft Bearing Tool - Big Twin

Inner Cam Bearing Install Tool Use to install inner cam bearings Made in the U.S.A.

Jims 1275 - Crankshaft Bearing Tool - Twin Cam

Crankshaft Bearing Tool Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in the U.S.A.

Jims 95760-TB - Camshaft Bearing - Puller - Big Twin

Inner Cam Bearing Removal Tool Used to remove inner cam bearing without damaging the crankcase Tool is also designed to keep rollers from falling into the crankcase Comes with instructions Made...

Jims 94804-57 - Rocker Bush Remover - Twin Cam

Rocker Bushing Reaming Tool Use to ream rocker bushings to a factory fit of .0007” - .0012” in line with each other This precise line reamer is capable of a 24 finish or better Made in the U.S.A.

Jims 1283 - Camshaft Chain Tensioner Tool

Cam Chain Tensioner Tool Designed to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams Also checks spring loads on chain tensioners Comes with...

Jims 94547-80A - Sprocket Shaft Bearing Race Tool

Sprocket Shaft Bearing Race Tool Must use with JIMS® Race and Bearing Install Handle (PART# DS-196042) Used to remove and install Timken® bearing race on motor cases Made in the U.S.A.

Jims 97273-60 - Camshaft Bearing Tool - XL

Inner Cam Bearing Install Tool Use to install inner cam bearings Made in the U.S.A.

Jims 96385-78A - Shift Fork Gauge - 4-Speed - Big Twin

Shift Fork Gauge This tool checks alignment of Big Twin transmission shift forks Made in the U.S.A.

Jims 1743 - Swingarm Bushing Tool

Swingarm Bushing Tool Allows installation of delicate, silicone cleveblock bushings in swingarm without damage Tool presses on outer sleeve of bushing Can be used with or without a press

Jims 35820-86 - Transmission Gear Spacing Tool - XL

Gear Spacing Tool Used to align main and countershafts when checking proper gear spacing Made in the U.S.A.

Jims 1030-TS - Socket - Crank Pin - Nut - Big Twin

Flywheel Socket Machined for 100% nut-to-socket and drive-end contact Eliminate nut rounding and risk of injury Made in the U.S.A.

Jims 96780-58A - Piston Pin Lock Ring Tool - Big Twin

Piston Pin Lock Ring Tool Use to install lock ring (Harley-Davidson® No. 22582-52) in piston having .515” inner diameter wrist pins, like most aftermarket pistons This tool will install “spiral...

Jims 95560-57 - Access Cover Tool - Transmission - Big Twin

Transmission Access Cover Puller Tool Use to remove transmission access covers, which are press-fit on two dowel pins Made in the U.S.A.

Jims 95724-57 - Tappet Guide Puller - Tool - XL

Tappet Guide Puller Tool Used to remove press-fit tappet guides from crankcase Made in the U.S.A.

Jims 94555-55A - Pinion Nut Socket - Big Twin

Pinion Gear Nut Socket Use to remove or secure pinion gear nut to pinion gear shaft Made in the U.S.A.

Jims 95760-TP - Pinion Bearing Puller - Big Twin

Pinion Bushing Puller Use to remove pinion bushing from cam cover in one easy operation Use with JIMS® Cam Cover Holder Made in the U.S.A.

Jims 1010 - Rod Alignment Tool - Evolution

Rod Alignment Tool Use to check rod straightness without removing the rods from the cases Made in the U.S.A.

Jims 1051 - Wrist Pin Bushing Tool

Connecting Rod Wrist Pin Bushing Tool Used to remove and install wrist pin bushings without removing connecting rods from crankcases Comes with instructions Made in the U.S.A.

Jims 1032-TS - Socket - Shaft Nut - Big Twin

Flywheel Socket Machined for 100% nut-to-socket and drive-end contact Eliminate nut rounding and risk of injury Made in the U.S.A.