Jims

Jims 5800 - Flywheel Puller Tool - Indian

Flywheel Puller Tool Eliminates potential damage to the flywheel when used in this application Ensures good and solid engagement when using the puller Made in the U.S.A.

Jims 5813 - Main Bearing Remover and Installer Tool - M8

Main Bearing Remover and Installer Not only removes the left and right main bearing without damaging the case, it also provides correct alignment and depth during installation High levels of...

Jims 5830 - Main Seal Remover Tool - Left

Main Seal Installer/Remover For use on Milwaukee Eight series engines

Jims 5808 - Valve Spring Compression Collar Tool - M8

Valve Spring Collar Valve spring collar allows existing compressor to remove smaller valves on M8 engines For use with JIMS® Valve Spring Compressor Tool (PART# DS-196013) Made in the U.S.A.

Jims 5828 - Cylinder Head Holder Tool - M8

Two-Sided Head Holder Tool Allows you to easily position head for all types of work Use to hold head in vice through spark plug hole For use with Milwaukee Eight engine series Has 14 mm and 12 mm...

Jims 1042-7 - Expander Dowel Tool

Bearing Expander Rod Removes and installs 3/4", 1", and 25 mm wheel bearings with or without (Anti-Lock Brake System) ABS Made in the U.S.A.

Jims 1278-3 - Camshaft Bearing Installation

Replacement Drive Replacement drive for JIMS® Cam Bearing Installation Tool

Jims 952 - Balancer Shift Alignment Tool

Balancer Shaft Sprocket Alignment Tool Takes the guesswork out of setting up your balancer shaft sprocket and chain alignment Made in the U.S.A.

Jims 2240-11-4 - Adapter - Valve Guide - Insert - 7 mm

Valve Guide Adapter Adapters are supported by a stand that makes it easy to press valve guides in and out Adapters for working on 7 mm valve guides Made in the U.S.A.

Jims 780 - Tester Tool - Seal Leak

Interconnect Seal Leak Testing Tool Required to seal the oil passage way from right case to the balancer tensioner plate; leaking can cause over oiling of the lower end that decreases horsepower...

Jims 1090 - Tester - Valve Spring

Mini Valve Spring Tester Tool fits any dual rate or conical valve spring with an O.D. no larger then 1.6” diameter Works with bench vise, arbor, screw hydraulic or drill press 0 to 1000 P.S.I...

Jims 915 - Installation Inner Ball Bearing Tool

Balancer Inner Bearing Installer Accurately and safely install the inner balancer bearing mounted in the left engine case All done on a work bench without using an arbor press Designed for early...

Jims 902 - Motor Stand - Blue - Twin Cam

Motor Stand Makes working on motors easier with better access Made in the USA

Jims 933 - Thread Chaser - SAE

Thread Chaser Tap Set An inexpensive way to clean up threads on frames or other parts that have been powder-coated or painted Includes coarse sizes; 1/4"-20, 5/16"-18, 3/8"-16, 7/16"-14, 1/2"-13,...

Jims 937 - Valve Guide Remover - 7 mm

Shoulderless Valve Guide Tool Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A.

Jims 786 - 6-Speed Seal Installation Tool - '06-'16

Cruise Drive Main Case Seal Installer Harley-Davidson’s® new 6-speed transmission is a very stout piece of engineering, incorporating some of the best bearings made JIMS® has developed a driver...

Jims 787 - Camshaft Bearing Installation Tool - '99-'17 Twin Cam

Cam Bearing Installation Tool Designed to press from the letter side of the inner cam bearing to eliminate any damage to the bearings, cam or case Will set bearings .023"-.028" below case surface ...

Jims 765 - Pump/Test Stand - Hydraulic Tappet - Big Twins

Tappet Pump and Test Stand Helps diagnose loose or spongy tappets that could eventually lead to bleed-down issues or sticky tappets that won't pump up due to poor hydraulic unit fitment Allows...

Jims 908 - Feeler Gauge - Set

Feeler Gauge Set Tool includes two gauge holders and the following size gauge inserts: .002", .003", .004", .005", .006", .008", .009", .010" and .011" New innovative feeler gauge holder cures the...

Jims 746 - Hydraulic Tappet - Go-No-Go™

Tappet Adjustment Tool Only when the tip fits nicely with no endplay is the tappet properly adjusted, if the tip doesn’t fit, OR if there is up and down endplay, the tappet is out of adjustment ...

Jims 759 - Dipstick Tool - Socket

Dipstick Removal Tool Allows riders and mechanics to quickly and safely remove engine oil level dipstick that lies precariously close to a scorching hot exhaust pipe Has square hole for 3/8"...

Jims 3200 - Gap Tool - Piston Ring End - Flange

Piston Ring End Gap Tool This tool makes measuring ring end gap faster, more accurate and eliminate the guess work Flanged design allows piston ring to fit squarely in cylinder bore every time ...

Jims 766 - Adapter - Hydraulic Tappet - EVO

Hydraulic Tappet Adapter Adapter for Harley-Davidson® Evolution hydraulic tappets Must use in conjunction with JIMS® tappet pump and test stand part# 3801-0192.

Jims 941 - Oil Filter Tool - Slim

Slim Oil Filter Wrench An exclusive design makes it much easier to navigate when working near both the oil cooler and the crankcase position sensor Allows you more room to work around exhaust...