Jims

Jims 33344-94 - Transmission Sprocket Spacer - Twin Cam

Transmission Sprocket Spacer — 5 Speed/6 Speed Smooth finish for a longer seal life 1.7" i.d. Made in the U.S.A.

Jims 25581-36 - Cam Bushing - Big Twin

Cam Cover Bushing Bushing is made from solid bronze bar stock Machined in one operation with a tolerance of .0002" Features a lead-in for ease of installation Made in the U.S.A.

Jims 1700 - Main/Shaft Clutch Gear Tool

Clutch Gear Puller Removes kick starter clutch gear successfully, without damage to the gear Made in the U.S.A.

Jims 1725 - Head Bearing Race Installer

Steering Head Bearing Race Installer Use to install steering head races, stock and custom, as well as install cups in the frame This tool pulls the races and cups in, straight and true, without any...

Jims 2201K - Staking Dowel Pins

Bushing Staking Dowel Pin Use on all bushings These pins hold bushing in place Made in the U.S.A.

Jims 8998K - Bearing

Transmission Door Bearing Made in the U.S.A.

Jims 2243 - Camshaft Seal Remover and Installer

Big Twin Cam Seal Tool Very simple tool, just mount tool in cover, screw in the two removing screws, turn center, and out comes the cam seal The new seal is then pressed in with the same tool,...

Jims 25586-37 - Cam Bushing - XL

Cam Cover Bushing Bushings are made from solid bronze bar stock Machined in one operation with a tolerance of .0002" Feature a lead-in for ease of installation Made in the U.S.A.

Jims 2244 - Fork Nut Socket - 35 mm - 3/8"

Top Nut Fork Socket Used to remove and install top fork nuts on fork tubes Rubber protector inside socket Will clear most handlebars Made in the U.S.A.

Jims 1047-TP - Crank Assembly Removal Tool - '55+ Big Twin

Crank Assembly Removing Tool This tool can only be used for removing the flywheel from the left case Will also press cases apart and break sealant bond Some case pressing will require a hard cap ...

Jims 95660-42 - 4-Speed Transmission Main Seal Tool - '36-'76 Big Twin

Big Twin Transmission Main Seal Tool Used to remove and install the main drive seal on specific Harley-Davidson® Big Twin models Made in the U.S.A.

Jims 35316-80 - Main Drive Gear Tool - 5-Speed

5-Speed Transmission Main Drive Gear Tool Installs the main drive gear without removing the transmission Used to remove and install the main drive gear Made in the USA

Jims 95960-52C - Clutch Hub Puller - '36-'90 Big Twin

Clutch Hub Puller Used to remove wet and dry clutch hubs without removing clutch release rod 4 bolts included for dry clutch removal Made in the U.S.A.

Jims 1041-TC - Camshaft Cover Holder Tool - '70-'99 Big Twin

Cam Cover Holding Tool Holds cam cover flat and helps prevent damage/scratches when removing and installing bushings Clamps in vice or Bridgeport™ mill Made in the U.S.A.

Jims 94660-37A - Center Shift Locknut

Transmission Sprocket Locknut Wrench Remove hex nut from end of main drive gear that secures the rear drive transmission pulley Inner collar will retain wrench to nut for safer work Extra-long...

Jims 1707 - Cleveblock Spreading Tool

Clevebloc Spreading Tool Spreads the swing arm cleveblocs allowing for installation of the swing arm Use to install the swing arm in a 5-Speed rubber mount frame Comes with instructions Made in...

Jims 94557-55A - Compensating Sprocket Socket Head - '55-'70

Compensating Sprocket Shaft Wrench Used to remove and install compensating nut Made in the U.S.A.

Jims 1012-70TB - Cam Bushing Installer

Cam or Piston Bushing Installer Drill Jig Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit included with jigs Use staking dowel pin Made in...

Jims 97225-55 - Sprocket Shift Bearing Installation Tool

Sprocket Shaft Bearing/Race/Seal Installation Tool Used on '84-'02 Big Twin to install the flywheel assembly to the left crankcase Timken® bearing Made in the U.S.A.

Jims 94547-80B - Sprocket Shaft Bearing Race Tool

Sprocket Shaft Bearing Race Tool Must use with JIMS® Race and Bearing Install Handle (PART# DS-196042) Used to remove and install Timken® bearing race on motor cases Made in the U.S.A.

Jims 1013-54TB - Pin Bushing Installer

Cam or Piston Bushing Installer Drill Jig Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit included with jigs Use staking dowel pin Made in...

Jims 1017-37TB - Cam Bushing Installer

Cam or Piston Bushing Installer Drill Jig Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit included with jigs Use staking dowel pin Made in...

Jims 34734-80 - Main Drive Gear Bearing/Seal Installer Tool - 5-Speed

Main Drive Gear Bearing/Seal Installation Tool Holds bearings and seal square to its bore, eliminating any marring Install both bearings and seal with use of a one-ton press Install bearings and...

Jims 97081-54 - Sprocket Shaft Bearing Press Tool

Sprocket Shaft Bearing Installation Tool Use on '55-'76 XL and K models to install the flywheel assembly into the left crankcase Timken® bearing Optional sleeves sold separately for use on '86-'03...