Jims

Jims 95960-52C - Clutch Hub Puller - '36-'90 Big Twin

Clutch Hub Puller Used to remove wet and dry clutch hubs without removing clutch release rod 4 bolts included for dry clutch removal Made in the U.S.A.

Jims 1041-TC - Camshaft Cover Holder Tool - '70-'99 Big Twin

Cam Cover Holding Tool Holds cam cover flat and helps prevent damage/scratches when removing and installing bushings Clamps in vice or Bridgeport™ mill Made in the U.S.A.

Jims 94660-37A - Center Shift Locknut

Transmission Sprocket Locknut Wrench Remove hex nut from end of main drive gear that secures the rear drive transmission pulley Inner collar will retain wrench to nut for safer work Extra-long...

Jims 97178-71 - Clutch Spring Compressor - '71-'84 XL

Clutch Spring Compressor Used to remove or install clutch components Made in the U.S.A.

Jims 1707 - Cleveblock Spreading Tool

Clevebloc Spreading Tool Spreads the swing arm cleveblocs allowing for installation of the swing arm Use to install the swing arm in a 5-Speed rubber mount frame Comes with instructions Made in...

Jims 94557-55A - Compensating Sprocket Socket Head - '55-'70

Compensating Sprocket Shaft Wrench Used to remove and install compensating nut Made in the U.S.A.

Jims 1012-70TB - Cam Bushing Installer

Cam or Piston Bushing Installer Drill Jig Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit included with jigs Use staking dowel pin Made in...

Jims 97225-55 - Sprocket Shift Bearing Installation Tool

Sprocket Shaft Bearing/Race/Seal Installation Tool Used on '84-'02 Big Twin to install the flywheel assembly to the left crankcase Timken® bearing Made in the U.S.A.

Jims 94547-80B - Sprocket Shaft Bearing Race Tool

Sprocket Shaft Bearing Race Tool Must use with JIMS® Race and Bearing Install Handle (PART# DS-196042) Used to remove and install Timken® bearing race on motor cases Made in the U.S.A.

Jims 1073 - Cylinder Torque Plates - '66-'99 Big Twin

Cylinder Torque Plate Kit Torque plates must be used when boring or honing late-model aluminum cylinders Simulate running stress conditions Come with instructions Made in the U.S.A.

Jims 1023-70 - Camshaft Bushing Line Reamer - '70-'99 Big Twin

Cam Bushing Line Reaming Tool Use to line ream cam cover bushing to size, from inner cam bearing, for a true center line between the two dimensions Finished size will be .0008"-.0015" over the cam...

Jims 1013-54TB - Pin Bushing Installer

Cam or Piston Bushing Installer Drill Jig Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit included with jigs Use staking dowel pin Made in...

Jims 1017-37TB - Cam Bushing Installer

Cam or Piston Bushing Installer Drill Jig Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit included with jigs Use staking dowel pin Made in...

Jims 34734-80 - Main Drive Gear Bearing/Seal Installer Tool - 5-Speed

Main Drive Gear Bearing/Seal Installation Tool Holds bearings and seal square to its bore, eliminating any marring Install both bearings and seal with use of a one-ton press Install bearings and...

Jims 97081-54 - Sprocket Shaft Bearing Press Tool

Sprocket Shaft Bearing Installation Tool Use on '55-'76 XL and K models to install the flywheel assembly into the left crankcase Timken® bearing Optional sleeves sold separately for use on '86-'03...

Jims 33096-54B - Kickstarter Shaft

Kickstarter Shaft Precision-machined replacement shaft Made in the U.S.A.

Jims 33096-54AL - Kickstarter Shaft - 4-Speed Big Twin

Kickstarter Shaft Precision-machined replacement shaft Made in the U.S.A.

Jims 35125-37 - Mainshaft Bearing Race - 4-Speed Big Twin

Transmission Bearing Sold individually, unless noted.

Jims 23909-80 - Sprocket Shaft - Big Twin

Motor Sprocket Shaft Made in the U.S.A.

Jims 1800 - Hydrosolid Tappet

Hydrosolid Tappets Perform like a hydraulic tappet up to 5500 rpm, then turn into a solid tappet When they turn into solid tappets, it adds approximately three to six more usable horsepower ...

Jims 2474-1 - Tappet - Standard Solid - Big Twin

Powerglide™ Tappets These tappets will run in cast iron or aluminum tappet blocks Recommend fitting the tappets to the blocks with a clearance of .0007" to .0012" Produced from billet bearing...

Jims 24006-80/83 - Pinion Gear Shaft - Big Twin

Pinion Gear Shaft Made in the U.S.A.

Jims 2475-1 - Standard Solid Tappet - Big Twin

Powerglide™ Tappets These tappets will run in cast iron or aluminum tappet blocks Recommend fitting the tappets to the blocks with a clearance of .0007" to .0012" Produced from billet bearing...

Jims 2476-1 - Tappet - Standard Solid - Big Twin

Powerglide™ Tappets These tappets will run in cast iron or aluminum tappet blocks Recommend fitting the tappets to the blocks with a clearance of .0007" to .0012" Produced from billet bearing...