Motion Pro

Motion Pro 08-0137 - Clutch Removal Tool - XL/Big Twin

Replacing the clutch on Harley-Davidson� is a lot easier and faster Durable low friction brass thrust washer

Motion Pro 08-0143 - Hydraulic Brake Bleeder - 1050062

Unique check valve lets fluid and air escape while preventing air from re-entering the system Universal tool makes bleeding brakes a one-person job Will not bleed air from a dry system Instructions and hose included Made in the U.S.A.

Motion Pro 08-0144 - Spring Fork Compress Tool

Assists in the disassembly and assembly of springer-type front forks on Harley-Davidson motorcycles Made in the U.S.A.

Motion Pro 08-0145 - T-Handle Socket Tool - 4-Piece

Hex socket extends only part of the way into the socket to allow the nut to be held flush with the end for easier, hands-free starting Deep sockets allow nuts to be driven over long threaded bolts Slim outside diameter allows sockets to fit in tight...

Motion Pro 08-0153 - Side Case Puller - Harley-Davidson�

Used to remove the right side-case cover Includes bracket, puller bolt and set screws Made in the U.S.A.

Motion Pro 08-0182 - Cable Luber - 1050027

Clamps over housing and wire allowing an aerosol can to be connected Once lube runs out the far end, the cable is lubricated Used to inject lubricant into cable housing

Motion Pro 08-0183 - Valve Core Remover - 1049876

Allows for easy removal and installation of standard valve cores in tubed or tubeless valve stems (Schrader valve) Perfect tool pack accessory

Motion Pro 08-0186 - Pliers - Snap Ring

Economical pliers easily work with both inside and outside opening snap rings or clips Includes three extra sets of tips: one additional straight tip and two offset or angle tips

Motion Pro 08-0189 - Deluxe Auxiliary Fuel Tank

For use with fuel-injected models with external fuel pumps as well as standard carburetor-equipped motorcycles Upgraded petcock for easier opening and closing Built-in fuel return line and breather on cap for use on fuel-injected motorcycles ...

Motion Pro 08-0230 - Pliers - Masterlink

One tip is shorter and notched to be placed on the pin, which allows the longer end to push the clip Designed to simplify installation and removal of clip-type masterlinks

Motion Pro 08-0339 - Screw - Tappet Tool - Oil Filter

O-ring design retains the tool in wrench or socket while flange design allows downward force to be applied to tool Designed for use with 7/16" combination wrench to allow for maximum rotation without touching engine cases For use on big twin...

Motion Pro 08-0350 - Belt Tension Gauge Tool

Designed to work with all belt drive models with a 10 lb. specification New L shaped pad fits all belt sizes Graduated scale for easy reference Compact design

Motion Pro 08-0357 - Rim Protector Pair 2

Protects wheels from scratches and dings caused by tire changing tools Include retrieval cord for easy use

Motion Pro 08-0359 - 1.4" Mini T-Handle Tool

Use handle drive to tighten/loosen fasteners and shaft drive for quick installation/removal of fasteners Compact shaft length for tight access and easy transport Use with sockets, hex drives, crow's foot, swivels, etc.

Motion Pro 08-0360 - 3/8" Mini T-Handle Tool

Use handle drive to tighten/loosen fasteners and shaft drive for quick installation/removal of fasteners Compact shaft length for tight access and easy transport Use with sockets, hex drives, crow's foot, swivels, etc.

Motion Pro 08-0380 - Wrench Adapter - Adjustable Torque

Will work with 6mm through 19mm metric and 1/4" through 3/4" fractional SAE combination wrenches Torque any fastener with a combination wrench or hex wrench 3/8" square drive is rated for a maximum torque of 100 lb/ft Made in the U.S.A.

Motion Pro 08-0412 - Fork Alignment

Will work on 27 mm-62 mm fork legs and tubes and on forks that are 140 mm to 220 mm (5.5" - 8.6") on center Quick and easy-to-use tool for aligning front forks to ensure they are parallel from top to bottom Proper alignment reduces stiction, enhancing...

Motion Pro 08-0427 - Gear Jammer

Gear Jammer Originally developed for removing and installing the primary gear on a Honda CRF450R/X Locks gears in place for easy installation and removal Allows tightening of lock nuts to proper torque setting Powerful magnet holds tool in place...

Motion Pro 08-0435 - Mount Bracket Tool

Wall Bracket works only with our new one piece design style T-Handle rack Features a quick release pin for removing and attaching the rack Includes built in bottle opener

Motion Pro 08-0452 - Wheel Weight - Steel - Silver - 90 oz Box

1/8 oz. segments measure .4" x .51" for proper alignment when used in combination with Motion Pro's 1/4 oz. weights Weights stick securely to spoked or cast wheels 1/4 oz. segments measure .500" x .750"

Motion Pro 08-0453 - Wheel Weight - Steel - Black - 90 oz Box

1/8 oz. segments measure .4" x .51" for proper alignment when used in combination with Motion Pro's 1/4 oz. weights Weights stick securely to spoked or cast wheels 1/4 oz. segments measure .500" x .750"

Motion Pro 08-0454 - Wheel Weight - Steel - Silver - 1/4" OZ

1/8 oz. segments measure .4" x .51" for proper alignment when used in combination with Motion Pro's 1/4 oz. weights Weights stick securely to spoked or cast wheels 1/4 oz. segments measure .500" x .750"

Motion Pro 08-0455 - Wheel Weight - Steel - Black - 1/4" OZ

1/8 oz. segments measure .4" x .51" for proper alignment when used in combination with Motion Pro's 1/4 oz. weights Weights stick securely to spoked or cast wheels 1/4 oz. segments measure .500" x .750"

Motion Pro 08-0467 - Chain Breaker/Press/Riveting Tool

Complete chain tool for most 520, 525 and 530 standard and O-ring chains Perfect for your tool pack if you have a chain with a rivet master link Will rivet hollow-nose master links (will not rivet solid soft-nose pins) Break, press, and rivet your...