Tools

Jims #1146 - Bearing Tool - Cam Side/Crankshaft - Installer/Remover - Twin Cam

Bearing Tool - Cam Side/Crankshaft - Installer/Remover - Twin CamFeaturesDesigned to protect engine cases by using a specially-designed support block to remove or install cam side crankshaft bearingMade in the USASpecsColor/FinishBlackTypeRemoverRiding...

Jims #1147 - Alternator Rotor Puller

Alternator Rotor PullerFeaturesA must-have tool for 45A charging systems; will also work on any Harley-Davidson® alternator system that has threaded puller holesTool protects threads on sprocket shaft from damage while pulling rotor free from its...

Jims #1148 - Rod Alignment Tool - Twin Cam

Rod Alignment Tool - Twin CamFeaturesUse to check rod straightness without removing the rods from the casesMade in the U.S.A.SpecsOutside Diameter0.927"Riding StyleStreetOverall Length4-1/2"Color/FinishSilverProduct NameAlignment...

Jims #1163 - Ball Shaft Retention Pins

Ball Shaft Retention PinsFeaturesLock into balancer shaft sprocket pinholes to prevent balancer from turning out of sync with flywheelUse to secure balancers when servicing the flywheel assemblyMade in the U.S.A.SpecsTypeBalancer Shaft...

Jims #1164 - Pistons Support Plate

Pistons Support PlateFeaturesSupport plate gives a non-marring, flat surface to push piston bottoms against when installing rings or cylindersMade in the U.S.A.SpecsApplicationCylinderProduct NameSupport PlateColor/FinishBlackRiding StyleStreetUnitsEach

Jims #1167 - Bearing Tool - Balancer Shaft/Removal - '00-'06 Softail

Bearing Tool - Balancer Shaft/Removal - '00-'06 SoftailFeaturesInstalling portion is designed to push on the outer diameter of bearings preventing any damage to the bearing or it's borePulls the bearings from the "B" motor case in one easy...

Jims #1168 - Inspection Plug Tool - Primary Cover

Inspection Plug Tool - Primary CoverFeaturesUse this tool to remove and install primary inspection plugMade in the USASpecsRiding StyleStreetColor/FinishBlackProduct NameInspection Plug ToolTypePrimary CoverUnitsEach

Jims #1169 - Compression Release Guide - Twin Cam

Compression Release Guide - Twin CamFeaturesInstallation kit includes fixture, drill bit, spot face bit and thread-tapping toolSimply drill, spot face, tap and install compression release valvesWorks on front and back head, with or without valves...

Jims #1236 - Ring - Piston - Compressor Kit

Ring - Piston - Compressor KitFeaturesFine-tooth ratcheting motion will compress the bands in small increments for accurate compressionWill not break or damage ringsMade in the U.S.A.SpecsColor/FinishBlackProduct NamePiston Ring CompressorPiston...

Jims #1275 - Crankshaft Bearing Tool - Twin Cam

Crankshaft Bearing Tool - Twin CamFeaturesDesigned to remove and replace the right crankcase bearingPress bearing in and out straight with no damage to the caseMade in the U.S.A.SpecsRiding...

Jims #1276 - Pin Remover - Wrist

Pin Remover - WristFeaturesCan be used easily by one person, no need to get another technician to hold the piston while drifting the pin in or outThis new JIMS® tool will cut the time it takes to remove and install wrist pinsMade in the U.S.A...

Jims #1277 - Camshaft Remover and Installer

Camshaft Remover and InstallerFeaturesThis multi-function tool will remove and replace front and rear camshafts and the ball bearings in the Twin Cam 88It provides the precision alignment of the camshaft to ensure a smooth press in and out of the support...

Jims #1278-3 - Camshaft Bearing Installation

Camshaft Bearing InstallationFeaturesReplacement drive for JIMS® Cam Bearing Installation ToolSpecsStyleReplacementTypeBearing InstallerApplicationCamUnitsEachColor/FinishBlackProduct NameDriver SocketRiding StyleStreet

Jims #1279 - Inner Camshaft Bearing

Inner Camshaft BearingFeaturesUsed to remove inner cam bearing without damaging the crankcaseTool is also designed to keep rollers from falling into the crankcaseComes with instructionsMade in the U.S.A.SpecsApplicationCamProduct NameBearing...

Jims #1280 - Camshaft Bearing Puller - Twin Cam

Camshaft Bearing Puller - Twin CamFeaturesOnce the camshafts are removed from the support plate this tool will remove the bearing from the camshaftRemoves bearing straight without binding or slippingMade in the U.S.A.SpecsUnitsEachTypeBearing...

Jims #1283 - Camshaft Chain Tensioner Tool

Camshaft Chain Tensioner ToolFeaturesDesigned to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble camsAlso checks spring loads on chain tensionersComes with instructionsMade in the U.S.A.SpecsRiding...

Jims #1284 - Holding Tool - Connecting Rod - V-Twin

Holding Tool - Connecting Rod - V-TwinFeaturesHolds the rods in place when reaming or honing the wrist pin bushingsMade in the USAFor most V-Twin and Buell Blast applications.SpecsColor/FinishBlueUnitsKitRiding StyleStreetTypeConnecting Rod

Jims #1285 - Cam/Crank Lock Tool - Sprocket

Cam/Crank Lock Tool - SprocketFeaturesDesigned to lock the camshafts and crankshaft sprockets when removing, replacing and torquing the sprocket boltsComes with instructionsMade in the U.S.A.SpecsColor/FinishBlackUnitsEachApplicationCrankshaftTypeDrive...

Jims #1288 - Crankshaft Guide - '99-'17 Twin Cam

Crankshaft Guide - '99-'17 Twin CamFeaturesSpreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel assemblyMade in the U.S.A.SpecsUnitsEachApplicationCrankcaseProduct NameCrankshaft GuideColor/FinishGrayRiding...

Jims #1658 - Shifter Shaft Sleeve Tool - Transmission - For 6-Speed

Shifter Shaft Sleeve Tool - Transmission - For 6-SpeedFeaturesCan be used to remove, install replacement or upgrade shifter shaft sleeve, assembly and drumUse to install shifter shaft sleeveMade in the USASpecsProduct NameShifter Shaft Sleeve...

Jims #1664 - Shifter Shaft Sleeve Tool - Transmission - For 5-Speed

Shifter Shaft Sleeve Tool - Transmission - For 5-SpeedFeaturesCan be used to remove, install replacement or upgrade shifter shaft sleeve, assembly and drumUse to install shifter shaft sleeveMade in the USASpecsColor/FinishBlackUnitsEachRiding...

Jims #1665 - Pinion Gear Tool - XL

Pinion Gear Tool - XLFeaturesUse to lock pinion gear when torquing the pinion gear nutSimple to use; just align underneath gear and screw into caseMade in the U.S.A.SpecsProduct NameLocking ToolColor/FinishBlackStyleDrill PlateApplicationPinion...

Jims #1666 - Crank Lock Tool - XL

Crank Lock Tool - XLFeaturesUse to lock pinion gear when torquing the pinion gear nutSimple to use; just align underneath gear and screw into caseMade in the U.S.A.SpecsApplicationPinion GearStyleDrill PlateColor/FinishBlackProduct NameLocking ToolRiding...

Jims #1672 - Crankshaft Bearing Tool

Crankshaft Bearing ToolFeaturesDesigned to remove and replace the right crankcase bearingPress bearing in and out straight with no damage to the caseMade in the U.S.A.SpecsColor/FinishBlackApplicationCrankcaseRiding StyleStreetStyleRightUnitsEachProduct...