Miscellaneous Tools

110" PISTON PIN CLIP REMOVER AND INSTALLER

Weight: 0.8900 Incorrect piston pin clip removal can damage the piston and incorrect installation can damage the clip. Damaged clips can come out during engine operation, causing catastrophic failure. This tool is designed exclusively for the...

5 SPEED MAIN CASE SEAL INSTALLER TOOL

Weight: 0.00 We now offer a new version of our Cruise Drive 6 Speed shaft seal tool to fit 5 speed transmissions. Like its drive counterpart, it ensures correct alignment, seal protection and depth when installing the seal. JimsFits Big Twin 1985/2006...

AXLE INSTALLATION GUIDE

Weight: 0.208 Installation of motorcycle axles has always been problematic. Trying to align the wheel with the other components such as swing arms, caliper brackets, wheel hubs and spacers can be frustrating, especially when trying to do the job alone...

BALANCER SCISSOR GEAR ALIGNMENT SCREW FOR MILWAUKEE EIGHT

Weight: 0.00 This tool holds the two halves of the spring loaded scissor balancer gear in alignment before removal for easy installation. No more fumbling with screwdrivers while trying to align the gear in place. The screw is brightly colored to remind...

CABLE LUBER FOR ALL MODELS

Weight: 0.0920 Designed to simplify the required lubrication process on throttle, clutch and brake cables. By using an aerosol cable lubricant like our 05098, you can power lube the cable in seconds. Made from anodized extruded aluminum for years of...

FERRULE INSTALLATION TOOL FOR "CUT TO FIT" BRAIDED BRAKE HOSE

Weight: 0.20Used to separate the braided stainless steel jacket away from the inner lining & open the bore for easy installation of the ferruleGoodridgeFerrule Tool for -3 (dash three) hoseBy: GOODRIDGE USA INC

INNER PRIMARY BEARING AND SEAL REMOVAL / INSTALLATION KIT

Weight: 0.00 When it comes to servicing the inner primary bearing and seal do it the Jims way.  This American made tool has a lifetime warranty and drives the bearing and seal perpendicular to the case without an arbor press. We have taken its proven...

MAIN BEARING REMOVER AND INSTALLER FOR MILWAUKEE EIGHT 2017/LATER

Weight: 5.266 The Milwaukee-Eight® engine uses a completely unique engine case main bearing. With this in mind, Jims is proud to introduce a main bearing remover and installer designed just for the Milwaukee-Eight®. High levels of precision and...

MILWAUKEE EIGHT HEAD HOLDER TOOL

Weight: 0.00 Different spark plug holes in the Miilwaukee-Eight heads call for a different head holder, and we have it. The proven system of anchoring the head in a vice is now available from Jims for this new engine series. Our new tool is two sided,...

MILWAUKEE EIGHT TORQUE PLATES

Weight: 0.00 Aluminum cylinders cannot be accurately honed and measured without the use of torque plates. This torque plate kit for Milwaukee-Eight cylinders will simulate operating stress conditions when boring or honing the cylinders. These plates...

SWING ARM BEARING INSTALLER

Weight: 0.00 Swing arm bearings must be installed and aligned accurately to avoid unsafe handling and ensure control of the motorcycle. Both drive side and brake side bearings, which are different depths, can be easily and accurately installed with this...

VACUUM TAPPET "PUMP UP" TOOL

Weight: 0.00 The popular and effective bleed technology that is found in the Jims brake bleeding tool has now been applied to hydraulic lifters. A special jar designed for vacuum holds up to four hydraulic lifters in a convenient tray. Once vacuum is...

WRIST PIN REMOVER ADAPTER

Weight: 0.00 Use with existing Jims wrist pin remover tool Part #60833 purchased seperately. The new Milwaukee-Eight engine uses different wrist pins compared to other Harley Davidson engines. This tool quickly and easily removes the wrist pins in...

XL SPROCKET NUT SOCKET

Weight: 0.00 This short socket is designed specifically for XL models to remove, install, and properly tighten the front final drive sprocket/pulley. Although the much longer Big Twin socket will fit the nut, the mainshaft on XL models does not extend...