Tools

Jims #1700 - Main/Shaft Clutch Gear Tool

Main/Shaft Clutch Gear ToolFeaturesRemoves kick starter clutch gear successfully, without damage to the gearMade in the U.S.A.SpecsFor Engine Type4-SpeedRiding StyleStreetColor/FinishBronzeApplicationKick StarterUnitsEachProduct NamePullerTypeClutch Gear

Jims #1705 - Exhaust Drill Plate

Exhaust Drill PlateFeaturesWill position the seal evenly into the exhaust port of headTool can be used with exhaust flange nutsMade in the U.S.A.SpecsColor/FinishBlueProduct NameSeal InstallerApplicationExhaustRiding StyleStreetStyleDrill PlateUnitsEach

Jims #1707 - Cleveblock Spreading Tool

Cleveblock Spreading ToolFeaturesSpreads the swing arm cleveblocs allowing for installation of the swing armUse to install the swing arm in a 5-Speed rubber mount frameComes with instructionsMade in the U.S.A...

Jims #1710 - Outer Race Snap Ring

Outer Race Snap RingFeaturesUsed for removing and installing the Timken® bearing outer race snap ringA must for replacing rings in OEM and aftermarket casesMade in the U.S.A.SpecsProduct NameSnap Ring ToolApplicationTimken® BearingColor/FinishBlackRiding...

Jims #1720 - Main Bearing Remover - 5-Speed

Main Bearing Remover - 5-SpeedFeaturesRemoves old bearing straight and will not damage the transmission caseCan be used without removing transmission from the bikeMade in the U.S.A.SpecsColor/FinishBlueApplicationMain Drive GearFor Engine...

Jims #1725 - Head Bearing Race Installer

Head Bearing Race InstallerFeaturesUse to install steering head races, stock and custom, as well as install cups in the frameThis tool pulls the races and cups in, straight and true, without any damageMade in the U.S.A.SpecsApplicationSteering...

Jims #1726-1 - Bushing Reamer - Wrist Pin

Bushing Reamer - Wrist PinFeaturesSome wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications).Used to ream wrist pin bushings to the proper inner diameterCan be used with rods in or out of...

Jims #1726-2 - Bushing Reamer - Wrist Pin

Bushing Reamer - Wrist PinFeaturesSome wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications).Used to ream wrist pin bushings to the proper inner diameterCan be used with rods in or out of...

Jims #1726-3 - Bushing Reamer - Wrist Pin

Bushing Reamer - Wrist PinFeaturesSome wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications).Used to ream wrist pin bushings to the proper inner diameterCan be used with rods in or out of...

Jims #1743 - Swingarm Bushing Tool

Swingarm Bushing ToolFeaturesAllows installation of delicate, silicone cleveblock bushings in swingarm without damageTool presses on outer sleeve of bushingCan be used with or without a pressSpecsApplicationSwingarmRiding...

Jims #1776 - Compressor Fork - Front

Compressor Fork - FrontFeaturesAlso includes FLT adapter for FLT forks to eliminate direct contact with spring coil and special rod to pull up fork damper rodTool compresses springs in cartridge-style forks when servicing or rebuildingCan be mounted in...

Jims #2043 - Fork Nut Socket - 41 mm

Fork Nut Socket - 41 mmFeaturesEliminates possible burring of plug caused by wrenchesUsed to remove and install top fork-tube plugFits 41 mm forksMade in the U.S.A.SpecsColor/FinishBlackProduct NameDriver SocketTypeFork NutApplicationForkRiding...

Jims #2046 - Fork Seal Installer - 39 mm

Fork Seal Installer - 39 mmFeaturesLightly grease to keep from scratching fork tubesUsed to install fork and dust sealsMade in the U.S.A.SpecsApplicationForkFork Tube Diameter39 mmRiding StyleStreetColor/FinishBlackUnitsEachProduct NameSeal Installer

Jims #2047 - Fork Seal Installer - 41 mm

Fork Seal Installer - 41 mmFeaturesLightly grease to keep from scratching fork tubesUsed to install fork and dust sealsMade in the U.S.A.SpecsApplicationForkFork Tube Diameter41 mmProduct NameSeal InstallerColor/FinishBlackRiding StyleStreetUnitsEach

Jims #2049 - Fork Seal Installation Tool - 49 mm

Fork Seal Installation Tool - 49 mmFeaturesInstalls lower leg 49 mm fork seals squarely into the bore without damaging the seal lip surfaceDesigned for specific Harley-Davidson® models except inverted fork modelsTwo-piece design to aid in some assembly...

Jims #2188 - Camshaft Bearing Installer

Camshaft Bearing InstallerFeaturesEasily presses the inner cam bearing smoothly into the right case with the cases assembled to the proper depthMade in the U.S.A.SpecsApplicationCamUnitsEachTypeInner BearingColor/FinishBlackProduct NameBearing...

Jims #2201K - Staking Dowel Pins - 10 Pack

Staking Dowel Pins - 10 PackFeaturesHolds bushing in placeMade in the USASpecsProduct NameDowel PinTypeStakingRiding StyleStreetUnits10 PackColor/FinishSilver

Jims #2232 - Bearing Race Tool

Bearing Race ToolFeaturesRemoves and installs steering head bearing race on 84-16 Big Twin (except 14-16 Dressers), 86-16 XL and 94-02 Buell OEM frames (will also work on most aftermarket frames)Must be used with tool driver spacer and handle/driverMade...

Jims #2233 - Tappet Tool - Oil Filter Plug

Tappet Tool - Oil Filter PlugFeaturesRemoves oil screen without removing exhaustUsed to remove the tappet oil screen plugMade in the U.S.A.SpecsStyleScrewProduct NameTappet ToolTypeFilter Plug RemoverApplicationOil FilterRiding...

Jims #2234 - Primary Drive Lock Tool

Primary Drive Lock ToolFeaturesUse on all primaries between front primary chain and motor sprocketMade in the U.S.A.SpecsRiding StyleStreetApplicationPrimary (Drive)Product NameLocking ToolColor/FinishBlackMaterialDelrin® PlasticUnitsEach

Jims #2240-11-4 - Adapter - Valve Guide - Insert - 7 mm

Adapter - Valve Guide - Insert - 7 mmFeaturesAdapters are supported by a stand that makes it easy to press valve guides in and outAdapters for working on 7 mm valve guidesMade in the U.S.A.SpecsTypeValve Guide...

Jims #2243 - Camshaft Seal Remover and Installer

Camshaft Seal Remover and InstallerFeaturesVery simple tool, just mount tool in cover, screw in the two removing screws, turn center, and out comes the cam sealThe new seal is then pressed in with the same tool, square and flat for a no leak fitUse to...

Jims #2244 - Fork Nut Socket - 35 mm - 3/8"

Fork Nut Socket - 35 mm - 3/8"FeaturesUsed to remove and install top fork nuts on fork tubesRubber protector inside socketWill clear most handlebarsMade in the U.S.A.SpecsTypeRemoval ToolFork Tube Diameter35 mmApplicationForkProduct NameDriver...

Jims #2246 - Timken® Bearing Race Installer

Timken® Bearing Race InstallerFeaturesUsed to install bearing race straight into the left crankcaseA must for late-model casesMade in the U.S.A.SpecsStyleLeft SideColor/FinishSilverRiding StyleStreetTypeInstallationUnitsEachProduct NameBearing Race...