Jims

Jims 1004A - Clutch Hub Puller

Clutch Hub Puller Will also work on Big Twin motor sprocket, alternator cover and early XL clutches as well as many other applications Can be used on 3-, 5- or 10-finger clutch hubs and 45" clutch hubs Made in the U.S.A.

Jims 1012-70TB - Cam Bushing Installer

Cam or Piston Bushing Installer Drill Jig Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit included with jigs Use staking dowel pin Made in the U.S.A.

Jims 1013-54TB - Pin Bushing Installer

Cam or Piston Bushing Installer Drill Jig Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit included with jigs Use staking dowel pin Made in the U.S.A.

Jims 1017-37TB - Cam Bushing Installer

Cam or Piston Bushing Installer Drill Jig Use to install bushing and drill dowel pin hole to factory specification #31 jobber length HSS drill bit included with jigs Use staking dowel pin Made in the U.S.A.

Jims 1019 - 5-Speed Rebuild Kit

A Cut Above™ Time-Saver 5-Speed Transmission Master Kit Includes bearings, retaining rings, spacers, locknuts, gaskets and seals Made in the U.S.A.

Jims 1020 - 5-Speed Transmission Rebuild Kit - Big Twin

Transmission Rebuild Kit Includes all the necessary gaskets, seals, locks and bearings needed to completely rebuild a 5-, or 6-speed transmission Made in the U.S.A.

Jims 1021 - 5-Speed Transmission Rebuild Kit - Big Twin

Transmission Rebuild Kit Includes all the necessary gaskets, seals, locks and bearings needed to completely rebuild a 5-, or 6-speed transmission Made in the U.S.A.

Jims 1035 - 5-Speed Transmission Rebuild Kit - Big Twin

Transmission Rebuild Kit Includes all the necessary gaskets, seals, locks and bearings needed to completely rebuild a 5-, or 6-speed transmission Made in the U.S.A.

Jims 1041-TC - Camshaft Cover Holder Tool - '70-'99 Big Twin

Cam Cover Holding Tool Holds cam cover flat and helps prevent damage/scratches when removing and installing bushings Clamps in vice or Bridgeport™ mill Made in the U.S.A.

Jims 1045RR - Rocker Arms - Big Twin/XL

Roller Rocker Arms The lightest rocker arm available, but still has superior strength characteristics due to its design The strength of 660 bronze bushings and bearing-grade steel for the roller tip Extensively tested under extreme conditions to...

Jims 1046-36A - Rod Race Set - Big Twin

Rod Race Set Made from 52100 aerospace-quality Timken® bearing stock Made in the U.S.A.

Jims 1047-TP - Crank Assembly Removal Tool - '55+ Big Twin

Crank Assembly Removing Tool This tool can only be used for removing the flywheel from the left case Will also press cases apart and break sealant bond Some case pressing will require a hard cap Use to press flywheels from cases Made in the U.S.A.

Jims 1052 - Oil Pump Snap Ring Installer

Oil Pump Snap Ring Installer Just apply oil to ring expander, slip ring up to the big end of ring expander, hold up to the end of the shaft, then push ring onto the shaft with sleeve Easily install outer snap ring on oil pump shaft, without over...

Jims 1053 - Oil Pump Seal Installer

Oil Pump Seal Installer For use on all Big Twin aluminum oil pumps (except Twin Cam/M8) Easily installs oil pump seal below gear surface for a no-leak fit Made in the U.S.A.

Jims 1060 - 6-Speed Transmission Rebuild Kit - 6-Speed Screamin' Eagle

Transmission Rebuild Kit Includes all the necessary gaskets, seals, locks and bearings needed to completely rebuild a 5-, or 6-speed transmission Made in the U.S.A.

Jims 1062 - 6-Speed Transmission Rebuild Kit - 6-Speed Screamin' Eagle

Transmission Rebuild Kit Includes all the necessary gaskets, seals, locks and bearings needed to completely rebuild a 5-, or 6-speed transmission Made in the U.S.A.

Jims 1095 - Aluminum Lifter Blocks - Big Twin

Aluminum Lifter Blocks Kits include front lifter block, rear lifter block and gaskets Mounting screws must be purchased separately; 53-65 models use 1/4"-24 screws Made in the U.S.A.

Jims 1147 - Alternator Rotor Puller

Alternator Rotor Tool A must-have tool for 45A charging systems; will also work on any Harley-Davidson® alternator system that has threaded puller holes Tool protects threads on sprocket shaft from damage while pulling rotor free from its magnetic hold...

Jims 1164 - Pistons Support Plate

Piston Support Plate Support plate gives a non-marring, flat surface to push piston bottoms against when installing rings or cylinders Made in the U.S.A.

Jims 1168 - Primary Inspection Plug Tool

Primary Cover Inspection Plug Tool Use this tool to remove and install primary inspection plug Made in the U.S.A.

Jims 1285 - Cam/Crank Lock Tool - Sprocket

Sprocket Lock Tool Designed to lock the camshafts and crankshaft sprockets when removing, replacing and torquing the sprocket bolts Comes with instructions Made in the U.S.A.

Jims 1350K - Valve Spring Kit - Evolution - Big Twin

Valve Spring Kit Incorporate an interference double-spring design with a damper to control harmonics Engineered for maximum performance in severe applications such as high compression and big-inch street motors Kits include locks, retainers and spring...

Jims 1370 - Valve Keepers - Big Twin

Valve Lock Keys Made from the highest grade materials and heat-treated to JIMS strict standards Feature a 10° lock angle Work well with JIMS titanium valve spring retainers Made in the U.S.A.

Jims 1664 - Shifter Shaft Sleeve Tool

Shifter Shaft Sleeve Tool Can be used to remove, install replacement or upgrade shifter shaft sleeve, assembly and drum Use to install shifter shaft sleeve Made in the U.S.A.