Tools & Supplies

Jims #1052 - Oil Pump Snap Ring Installer

Oil Pump Snap Ring InstallerFeaturesJust apply oil to ring expander, slip ring up to the big end of ring expander, hold up to the end of the shaft, then push ring onto the shaft with sleeveEasily install outer snap ring on oil pump shaft, without over...

Jims #1053 - Oil Pump Seal Installer

Oil Pump Seal InstallerFeaturesFor use on all Big Twin aluminum oil pumps (except Twin Cam/M8)Easily installs oil pump seal below gear surface for a no-leak fitMade in the U.S.A.SpecsUnitsEachColor/FinishBlackApplicationOil SystemProduct NameSeal...

Jims #1075 - Installer - Cylinder Stud

Installer - Cylinder StudFeaturesAssembly tool features a captive hardened ball bearing dimensionally set 1" from top of toolWorks on all Evolution Big Twin and XL modelsMade in the U.S.A.SpecsApplicationEngineRiding StyleStreetProduct NameStud...

Jims #1090 - Tester - Valve Spring

Tester - Valve SpringFeaturesTool fits any dual rate or conical valve spring with an O.D. no larger then 1.6” diameterWorks with bench vise, arbor, screw hydraulic or drill press0 to 1000 P.S.I. gaugeMade in the U.S.A.SpecsApplicationValveProduct...

Jims #1111 - Camshaft Pinion Gauge Pins 108

Camshaft Pinion Gauge Pins 108FeaturesUse to check pinion gear for pitch diametersCheck service manual for sizing chartMade in the U.S.A.SpecsGauge0.108"Measurement SystemSAETypePinion Gear GaugeUnitsPairColor/FinishGrayProduct NamePinRiding...

Jims #1146 - Bearing Tool - Cam Side/Crankshaft - Installer/Remover - Twin Cam

Bearing Tool - Cam Side/Crankshaft - Installer/Remover - Twin CamFeaturesDesigned to protect engine cases by using a specially-designed support block to remove or install cam side crankshaft bearingMade in the USASpecsColor/FinishBlackTypeRemoverRiding...

Jims #1147 - Alternator Rotor Puller

Alternator Rotor PullerFeaturesA must-have tool for 45A charging systems; will also work on any Harley-Davidson® alternator system that has threaded puller holesTool protects threads on sprocket shaft from damage while pulling rotor free from its...

Jims #1148 - Rod Alignment Tool - Twin Cam

Rod Alignment Tool - Twin CamFeaturesUse to check rod straightness without removing the rods from the casesMade in the U.S.A.SpecsOutside Diameter0.927"Riding StyleStreetOverall Length4-1/2"Color/FinishSilverProduct NameAlignment...

Jims #1163 - Ball Shaft Retention Pins

Ball Shaft Retention PinsFeaturesLock into balancer shaft sprocket pinholes to prevent balancer from turning out of sync with flywheelUse to secure balancers when servicing the flywheel assemblyMade in the U.S.A.SpecsTypeBalancer Shaft...

Jims #1164 - Pistons Support Plate

Pistons Support PlateFeaturesSupport plate gives a non-marring, flat surface to push piston bottoms against when installing rings or cylindersMade in the U.S.A.SpecsApplicationCylinderProduct NameSupport PlateColor/FinishBlackRiding StyleStreetUnitsEach

Jims #1167 - Bearing Tool - Balancer Shaft/Removal - '00-'06 Softail

Bearing Tool - Balancer Shaft/Removal - '00-'06 SoftailFeaturesInstalling portion is designed to push on the outer diameter of bearings preventing any damage to the bearing or it's borePulls the bearings from the "B" motor case in one easy...

Jims #1168 - Inspection Plug Tool - Primary Cover

Inspection Plug Tool - Primary CoverFeaturesUse this tool to remove and install primary inspection plugMade in the USASpecsRiding StyleStreetColor/FinishBlackProduct NameInspection Plug ToolTypePrimary CoverUnitsEach

Jims #1169 - Compression Release Guide - Twin Cam

Compression Release Guide - Twin CamFeaturesInstallation kit includes fixture, drill bit, spot face bit and thread-tapping toolSimply drill, spot face, tap and install compression release valvesWorks on front and back head, with or without valves...

Jims #1236 - Ring - Piston - Compressor Kit

Ring - Piston - Compressor KitFeaturesFine-tooth ratcheting motion will compress the bands in small increments for accurate compressionWill not break or damage ringsMade in the U.S.A.SpecsColor/FinishBlackProduct NamePiston Ring CompressorPiston...

Jims #1275 - Crankshaft Bearing Tool - Twin Cam

Crankshaft Bearing Tool - Twin CamFeaturesDesigned to remove and replace the right crankcase bearingPress bearing in and out straight with no damage to the caseMade in the U.S.A.SpecsRiding...