Tools & Hardware

Jims #981 - Main Drive Gear Tool - Cruise Drive/6-Speed

Main Drive Gear Tool - Cruise Drive/6-SpeedFeaturesHolds the main drive gear square to its bearing bore, eliminating any marring of gear or bearingsInstalls the main drive gear without removing the transmissionMade in the USASpecsColor/FinishBlackProduct...

Jims #984 - Door Puller - Transmission - '06 Dyna/'07-'17 Big Twin

Door Puller - Transmission - '06 Dyna/'07-'17 Big TwinFeaturesRemoves transmission door with gears and shaft attachedMade in the USAPuller will not damage door bearings.SpecsProduct NameDoor PullerRiding...

Jims #985 - Removal Tool - Shifter Shaft

Removal Tool - Shifter ShaftFeaturesLoosens and removes both shifter shafts from transmission door, allowing further disassembly of transmissionMade in the USASpecsColor/FinishBlackTypeShifter ShaftUnitsEachRiding StyleStreetProduct NameRemoval Tool

Jims #986 - Main Drive Gear Bearing/Seal Installer Tool - Cruise Drive/6-Speed

Main Drive Gear Bearing/Seal Installer Tool - Cruise Drive/6-SpeedFeaturesHolds bearings and seal square to its bore, eliminating any marringInstall both bearings and seal with use of a one-ton pressInstall bearings and seal to correct depthMade in the...

Jims #987 - Main Bearing Installer Tool - Cruise Drive/6-Speed

Main Bearing Installer Tool - Cruise Drive/6-SpeedFeaturesSafely installs new main transmission case bearing; does not remove bearingHolds bearing square to its bore, eliminating any marring of bearing boreMade in the...

Jims #988 - Valve Spring - Compressor

Valve Spring - CompressorFeaturesUsed to remove and replace valve and new-style conical valve springRequires use of JIMS Valve Spring Compressor ToolMade in the U.S.A.SpecsProduct NameSpring CompressorRiding StyleStreetUnitsEachApplicationValve...

Jims #989 - Sprocket Locknut Wrench - Main Drive Gear

Sprocket Locknut Wrench - Main Drive GearFeaturesRemoves hex nut from end of main drive gear that secures the rear drive transmission pulleyExtra-long two-piece designMade in the USAInner collar will retain wrench to nut for safer work.SpecsTypeMain...

Jims #990 - Camshaft Assembly Tool - '07-'17 Twin Cam

Camshaft Assembly Tool - '07-'17 Twin CamFeaturesHolds both cams in an upright position while lowering cam support plate over both guides and cam journal guidesMade from a non-marring material that will not damage any of the cams' surfacesMade in the U.S...

Jims #991 - Case Splitting Tool - M8

Case Splitting Tool - M8FeaturesIn order to perform any type of lower end service or performance work, it is necessary to split the crankcase into halvesSimply install the tool on the primary side of the case, and easily split the cases by hand with a...

Jims #993 - Inner Camshaft Bearing Tool

Inner Camshaft Bearing ToolFeaturesUsed to remove inner cam bearing without damaging the crankcaseTool is also designed to keep rollers from falling into the crankcaseComes with instructionsMade in the U.S.A.SpecsApplicationCamTypeInner...

Jims #994 - Camshaft Locking Tool - Big Twin

Camshaft Locking Tool - Big TwinFeaturesDesigned to lock the camshafts and crankshaft sprockets when removing, replacing and torquing the sprocket boltsComes with instructionsMade in the U.S.A.SpecsUnitsEachApplicationCamshaftStyleSprocketTypeDrive Gear...

Jims #995 - Splitter Case - '07-'17 Twin Cam

Splitter Case - '07-'17 Twin CamFeatures"Breaks" the case sealant by pushing apart both case halvesUses included hand thread-in pushing screwFlywheels will be pushed from the left caseBolts to primary mounting holesMade in the U.S.A...

Jims 1046 - Clean-Up Kit - Shovelhead

Top-End Oiling Kit Kit includes special Powerglide tappets with Evolution-style pushrod seat, special Worksaver pushrods, chrome tappet blocks with gaskets and roller rocker arms Top-end is oiled through JIMS proven Powerglide™ tappets, then up through...

Jims 1162 - Caliper Piston Remover

Brake Caliper Piston Remover Prevents damage to pistons and cylinders when installing new seals and wipers Holds pistons square in their cylinder bores during removal Designed for front and rear 4-piston calipers Made in the U.S.A.

Jims 908 - Feeler Gauge - Set

Feeler Gauge Set Tool includes two gauge holders and the following size gauge inserts: .002", .003", .004", .005", .006", .008", .009", .010" and .011" New innovative feeler gauge holder cures the need to use bulky multi-feeler gauge tools while...