Tools & Hardware

Jims #1665 - Pinion Gear Tool - XL

Pinion Gear Tool - XLFeaturesUse to lock pinion gear when torquing the pinion gear nutSimple to use; just align underneath gear and screw into caseMade in the U.S.A.SpecsProduct NameLocking ToolColor/FinishBlackStyleDrill PlateApplicationPinion...

Jims #1666 - Crank Lock Tool - XL

Crank Lock Tool - XLFeaturesUse to lock pinion gear when torquing the pinion gear nutSimple to use; just align underneath gear and screw into caseMade in the U.S.A.SpecsApplicationPinion GearStyleDrill PlateColor/FinishBlackProduct NameLocking ToolRiding...

Jims #1672 - Crankshaft Bearing Tool

Crankshaft Bearing ToolFeaturesDesigned to remove and replace the right crankcase bearingPress bearing in and out straight with no damage to the caseMade in the U.S.A.SpecsColor/FinishBlackApplicationCrankcaseRiding StyleStreetStyleRightUnitsEachProduct...

Jims #1705 - Exhaust Drill Plate

Exhaust Drill PlateFeaturesWill position the seal evenly into the exhaust port of headTool can be used with exhaust flange nutsMade in the U.S.A.SpecsColor/FinishBlueProduct NameSeal InstallerApplicationExhaustRiding StyleStreetStyleDrill PlateUnitsEach

Jims #1710 - Outer Race Snap Ring

Outer Race Snap RingFeaturesUsed for removing and installing the Timken® bearing outer race snap ringA must for replacing rings in OEM and aftermarket casesMade in the U.S.A.SpecsProduct NameSnap Ring ToolApplicationTimken® BearingColor/FinishBlackRiding...

Jims #1720 - Main Bearing Remover - 5-Speed

Main Bearing Remover - 5-SpeedFeaturesRemoves old bearing straight and will not damage the transmission caseCan be used without removing transmission from the bikeMade in the U.S.A.SpecsColor/FinishBlueApplicationMain Drive GearFor Engine...

Jims #1726-1 - Bushing Reamer - Wrist Pin

Bushing Reamer - Wrist PinFeaturesSome wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications).Used to ream wrist pin bushings to the proper inner diameterCan be used with rods in or out of...

Jims #1726-2 - Bushing Reamer - Wrist Pin

Bushing Reamer - Wrist PinFeaturesSome wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications).Used to ream wrist pin bushings to the proper inner diameterCan be used with rods in or out of...

Jims #1726-3 - Bushing Reamer - Wrist Pin

Bushing Reamer - Wrist PinFeaturesSome wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications).Used to ream wrist pin bushings to the proper inner diameterCan be used with rods in or out of...

Jims #1743 - Swingarm Bushing Tool

Swingarm Bushing ToolFeaturesAllows installation of delicate, silicone cleveblock bushings in swingarm without damageTool presses on outer sleeve of bushingCan be used with or without a pressSpecsApplicationSwingarmRiding...

Jims #1776 - Compressor Fork - Front

Compressor Fork - FrontFeaturesAlso includes FLT adapter for FLT forks to eliminate direct contact with spring coil and special rod to pull up fork damper rodTool compresses springs in cartridge-style forks when servicing or rebuildingCan be mounted in...

Jims #1803 - Hydrosolid Tappet - XL

Hydrosolid Tappet - XLFeaturesPerform like a hydraulic tappet up to 5500 rpm, then turn into a solid tappetWhen they turn into solid tappets, it adds approximately three to six more usable horsepowerPrevent hydraulic pump at high rpmsMade in the U.S.A...

Jims #2043 - Fork Nut Socket - 41 mm

Fork Nut Socket - 41 mmFeaturesEliminates possible burring of plug caused by wrenchesUsed to remove and install top fork-tube plugFits 41 mm forksMade in the U.S.A.SpecsColor/FinishBlackProduct NameDriver SocketTypeFork NutApplicationForkRiding...

Jims #2046 - Fork Seal Installer - 39 mm

Fork Seal Installer - 39 mmFeaturesLightly grease to keep from scratching fork tubesUsed to install fork and dust sealsMade in the U.S.A.SpecsApplicationForkFork Tube Diameter39 mmRiding StyleStreetColor/FinishBlackUnitsEachProduct NameSeal Installer

Jims #2047 - Fork Seal Installer - 41 mm

Fork Seal Installer - 41 mmFeaturesLightly grease to keep from scratching fork tubesUsed to install fork and dust sealsMade in the U.S.A.SpecsApplicationForkFork Tube Diameter41 mmProduct NameSeal InstallerColor/FinishBlackRiding StyleStreetUnitsEach