Tools & Hardware

Jims #39361-69 - Seal Installation Tool - Sprocket Shaft

Seal Installation Tool - Sprocket ShaftFeaturesDesigned to press oil seal over sprocket shaft into caseMade in the U.S.A.SpecsUnitsEachColor/FinishBlackRiding StyleStreetApplicationSprocket ShaftProduct NameSeal Installer

Jims #5501 - Tool - Battery Lifter

Tool - Battery LifterFeaturesModeled after the larger tools made for automotive batteries, but is properly sized for Harley-Davidson® modelsEasily lifts batteries that have an extremely tight fit in the compartmentMade in the USASpecsRiding...

Jims #5502 - Tool - Clutch Adjustment - Ultimate

Tool - Clutch Adjustment - UltimateFeaturesAllows the quick and accurate tightening of the clutch adjusting screw jam nut without having the screw change positionIncludes the proper hex key Allen wrench, which conveniently stores in the tool handleMade...

Jims #5503 - Master Kit - Front/Rear Brake/Clutch

Master Kit - Front/Rear Brake/ClutchFeaturesConsists of a vacuum-bleed device with a transparent cap which forms a tight seal to the master cylinder and has a fitting to attach a vacuum pumpCleaner way to purge the system of air with less fluid used and...

Jims #5504 - Tappet Position Holder

Tappet Position HolderFeaturesTappet locations are clearly referenced on the tool, which also serves to protect the tappets from damage when removed from the engineSafely stores anti-rotation pins and tappets for proper and accurate installationMade in...

Jims #5506 - Magnetic Tappet Holder - Twin Cam and M8

Magnetic Tappet Holder - Twin Cam and M8FeaturesNever turn the engine over if the tappet will not spin with your fingers after adjustments were madeIt is very important that the engine is not rotated while pushrods are tightThe pushrod will spin with...

Jims #5507 - Lid Kit - Front Brake

Lid Kit - Front BrakeFeaturesConsists of a vacuum-bleed device with a transparent cap which forms a tight seal to the master cylinder and has a fitting to attach a vacuum pumpCleaner way to purge the system of air with less fluid used and a reduced...

Jims #5515 - Neck Bearing Tool

Neck Bearing ToolFeaturesTool has tapered drivers that ensure the correct installed alignment and depth of steering stem racesEliminates the risk of damaging the races and bearings during installationMade in the U.S.A...

Jims #5516 - Socket Tool - Sprocket Nut/Removal/Installation - Sportster

Socket Tool - Sprocket Nut/Removal/Installation - SportsterFeaturesEnsures the mainshaft on Harley-Davidson® Sportster models extends through the guidance collar for correct alignmentShort socket is specifically designed to remove, install and properly...

Jims #5517 - Shifter Mechanism Sleeve Tool - Removal/Installation

Shifter Mechanism Sleeve Tool - Removal/InstallationFeaturesA real time saver for removing and installing the shifter mechanism sleeve in cruise drive Big Twin transmissionsTool allows you to remove and install the sleeve (bushing) without having to...

Jims #5518 - Bushing Tool - Shifter Shaft

Bushing Tool - Shifter ShaftFeaturesTime-saving tool removes worn shift shaft bushings in Big Twin primaries without having to remove he inner primaryTools installs new bushings to the correct locationMade in the USAFor touring models with 5- or 6-speed...

Jims #5520 - Primary Locking Bar - XL

Primary Locking Bar - XLFeaturesImmobilizes primary driveAllows for tightening with a torque wrench or loosening with a breaker barPrevents damage to rotor or magnets sometimes caused by air-wrenchMade in the U.S.A.SpecsColor/FinishBlackRiding...

Jims #5530 - Fuel Tank - Remote

Fuel Tank - RemoteFeaturesTank is completely mobile, even when pressurized; canister does not need to be continuously connected to the air supplySmall enough to hang from a handlebar, be attached to a wall mount, work bench or rollaway tool chestTank...

Jims #5532 - Tappet - Vacuum

Tappet - VacuumFeaturesRemoves the risk of using the starting system to pump up the lifters or damage to the valve train at low rpm if the lifters are not fully bledSpecial jar, designed for vacuum, holds up to four hydraulic lifters in a convenient...

Jims #5534 - Socket - Compensator Bolt Driver - Torx

Socket - Compensator Bolt Driver - TorxFeaturesCorrect-style driver/socket for the compensating sprocket retaining fastenerMade in the USAFor use with Jim's part# 10500031 compensator bolt.SpecsStyleTorxUnitsEachTypeCompensator Bolt...