Jims

Jims #917 - Clip - Pushrod Cover

Clip - Pushrod CoverFeaturesWill install and remove the clip professionally with just one hand in secondsThis tool will NOT marr or slipMade in the U.S.A.SpecsApplicationPushrodRiding...

Jims #604 - Alignment Screws - Rocker Box

Alignment Screws - Rocker BoxFeaturesPrevents misalignment of cover, compromising of seal and potential rocker interferenceMade in the U.S.A.SpecsApplicationRocker Box CoverColor/FinishBlackProduct...

Jims #753 - Flywheel Lock with Tag - Mighty Bite - Blue - Twin Cam

Flywheel Lock with Tag - Mighty Bite - Blue - Twin CamFeaturesLocks flywheel in place when performing service work to the connecting rods or pistons with the cylinders off the engineFor use on Twin...

Jims 916 - Case Support Blocks

Twin Cam "B" Motor Case Support Blocks Aluminum blocks have inserted Delrin® pads that rest against case to prevent marring and to support the case Keeps case level when using bearing pullers to...

Jims #779 - Balancer Retainer Tool

Balancer Retainer ToolFeaturesHolds hydraulic tensioners in place that keep constant chain tension on counter balancer systemMade in the U.S.A.SpecsStyleHydraulicProduct NameTensioner HolderRiding...

Jims #993 - Inner Camshaft Bearing Tool

Inner Camshaft Bearing ToolFeaturesUsed to remove inner cam bearing without damaging the crankcaseTool is also designed to keep rollers from falling into the crankcaseComes with instructionsMade in...

Jims #2049 - Fork Seal Installation Tool - 49 mm

Fork Seal Installation Tool - 49 mmFeaturesInstalls lower leg 49 mm fork seals squarely into the bore without damaging the seal lip surfaceDesigned for specific Harley-Davidson® models except...

Jims #988 - Valve Spring - Compressor

Valve Spring - CompressorFeaturesUsed to remove and replace valve and new-style conical valve springRequires use of JIMS Valve Spring Compressor ToolMade in the U.S.A.SpecsProduct NameSpring...

Jims #966 - Starter Seal Tool

Starter Seal ToolFeaturesEasily aligns and installs starter jackshaft seal without distorting or damaging sealSeal is located in upper part of inner primary of Big TwinsMade in the U.S.A.SpecsProduct...

Jims #2312 - Primary Locking Bar Tool

Primary Locking Bar ToolFeaturesImmobilizes primary driveAllows for tightening with a torque wrench or loosening with a breaker barPrevents damage to rotor or magnets sometimes caused by...

Jims #1672 - Crankshaft Bearing Tool

Crankshaft Bearing ToolFeaturesDesigned to remove and replace the right crankcase bearingPress bearing in and out straight with no damage to the caseMade in the U.S.A...

Jims #956 - Replacement Sleeve - Timken Case Bearing Tool - Kit

Replacement Sleeve - Timken Case Bearing Tool - KitFeaturesSleeve is several times stronger than stock aluminum case material that standard bearings ride inReplacement sleeve kit for Timken® Case...

Jims #969 - O² Sensor Tool - Socket

O² Sensor Tool - SocketFeaturesRemove and install oxygen sensors on fuel-injected modelsSocket tool will withstand up to 125 ft.-lbs. of torqueMade in the USASpecsRiding StyleStreetUnitsEachDrive...

Jims #1075 - Installer - Cylinder Stud

Installer - Cylinder StudFeaturesAssembly tool features a captive hardened ball bearing dimensionally set 1" from top of toolWorks on all Evolution Big Twin and XL modelsMade in the U.S.A...

Jims #995 - Splitter Case - '07-'17 Twin Cam

Splitter Case - '07-'17 Twin CamFeatures"Breaks" the case sealant by pushing apart both case halvesUses included hand thread-in pushing screwFlywheels will be pushed from the left caseBolts...