Jims

Jims #2240-11-4 - Adapter - Valve Guide - Insert - 7 mm

Adapter - Valve Guide - Insert - 7 mmFeaturesAdapters are supported by a stand that makes it easy to press valve guides in and outAdapters for working on 7 mm valve guidesMade in the U.S.A...

Jims #780 - Tester Tool - Seal Leak

Tester Tool - Seal LeakFeaturesRequired to seal the oil passage way from right case to the balancer tensioner plate; leaking can cause over oiling of the lower end that decreases horsepower from oil...

Jims #1090 - Tester - Valve Spring

Tester - Valve SpringFeaturesTool fits any dual rate or conical valve spring with an O.D. no larger then 1.6” diameterWorks with bench vise, arbor, screw hydraulic or drill press0 to 1000 P.S.I...

Jims #915 - Installation Inner Ball Bearing Tool

Installation Inner Ball Bearing ToolFeaturesAccurately and safely install the inner balancer bearing mounted in the left engine caseAll done on a work bench without using an arbor pressDesigned for...

Jims #902 - Motor Stand - Blue - Twin Cam

Motor Stand - Blue - Twin CamFeaturesMakes working on motors easier with better accessMade in the USASpecsFeaturesFor Twin Cam B MotorMaterialSteelRiding StyleStreetColor/FinishBlueProduct NameMotor...

Jims #933 - Thread Chaser - SAE

Thread Chaser - SAEFeaturesAn inexpensive way to clean up threads on frames or other parts that have been powder-coated or paintedIncludes coarse sizes; 1/4"-20, 5/16"-18, 3/8"-16,...

Jims #937 - Valve Guide Remover - 7 mm

Valve Guide Remover - 7 mmFeaturesAvailable from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve sealsMade in the U.S.A.SpecsProduct NameValve Guide...

Jims #786 - 6-Speed Seal Installation Tool - '06-'16

6-Speed Seal Installation Tool - '06-'16FeaturesHarley-Davidson’s® new 6-speed transmission is a very stout piece of engineering, incorporating some of the best bearings madeJIMS® has developed a...

Jims #787 - Camshaft Bearing Installation Tool - '99-'17 Twin Cam

Camshaft Bearing Installation Tool - '99-'17 Twin CamFeaturesDesigned to press from the letter side of the inner cam bearing to eliminate any damage to the bearings, cam or caseWill set bearings ...

Jims #765 - Pump/Test Stand - Hydraulic Tappet - Big Twins

Pump/Test Stand - Hydraulic Tappet - Big TwinsFeaturesHelps diagnose loose or spongy tappets that could eventually lead to bleed-down issues or sticky tappets that won't pump up due to poor hydraulic...

Jims #746 - Hydraulic Tappet - Go-No-Go™

Hydraulic Tappet - Go-No-Go™FeaturesOnly when the tip fits nicely with no endplay is the tappet properly adjusted, if the tip doesn’t fit, OR if there is up and down endplay, the tappet is out of...

Jims #759 - Dipstick Tool - Socket

Dipstick Tool - SocketFeaturesAllows riders and mechanics to quickly and safely remove engine oil level dipstick that lies precariously close to a scorching hot exhaust pipeHas square hole for...

Jims #3200 - Gap Tool - Piston Ring End - Flange

Gap Tool - Piston Ring End - FlangeFeaturesThis tool makes measuring ring end gap faster, more accurate and eliminate the guess workFlanged design allows piston ring to fit squarely in cylinder bore...

Jims #941 - Oil Filter Tool - Slim

Oil Filter Tool - SlimFeaturesAn exclusive design makes it much easier to navigate when working near both the oil cooler and the crankcase position sensorAllows you more room to work around exhaust...

Jims #910 - Ring - Piston - Compressor Kit

Ring - Piston - Compressor KitFeaturesFine-tooth ratcheting motion will compress the bands in small increments for accurate compressionWill not break or damage ringsMade in the U.S.A.SpecsMeasurement...