Tools

Jims #785 - Jims Flywheel Runout Gauge Tool

Jims Flywheel Runout Gauge Tool

Jims #786 - 6-Speed Seal Installation Tool - '06-'16

6-Speed Seal Installation Tool - '06-'16FeaturesHarley-Davidson’s® new 6-speed transmission is a very stout piece of engineering, incorporating some of the best bearings madeJIMS® has developed a...

Jims #787 - Camshaft Bearing Installation Tool - '99-'17 Twin Cam

Camshaft Bearing Installation Tool - '99-'17 Twin CamFeaturesDesigned to press from the letter side of the inner cam bearing to eliminate any damage to the bearings, cam or caseWill set bearings ...

Jims #788 - Seal - Exhaust Gasket - Installer

Seal - Exhaust Gasket - InstallerFeaturesInstalls fragile exhaust seal with ease and will position seal evenly to exhaust port of headCan be used with exhaust flange nuts or JIMS handle sold...

Jims #900 - Main Drive Gear/Bearing Remover/Installer - 6-Speed

Main Drive Gear/Bearing Remover/Installer - 6-SpeedFeaturesComplete kit for servicing the main drive gear or the main bearing on the latest Harley-Davidson­­® 6-speed transmissionTool removes and...

Jims #901 - Main Drive Gear Remover Tool - Cruise Drive/6-Speed - Harley Davidson

Main Drive Gear Remover Tool - Cruise Drive/6-Speed - Harley DavidsonFeaturesRemoves the main drive gear from the main bearing correctly while in the transmission caseEliminates the need of an arbor...

Jims #902 - Motor Stand - Blue - Twin Cam

Motor Stand - Blue - Twin CamFeaturesMakes working on motors easier with better accessMade in the USASpecsFeaturesFor Twin Cam B Motor

Jims #906 - Jims Rear Axle Nut Torque Adapter Tool

Jims Rear Axle Nut Torque Adapter Tool

Jims #910 - Ring - Piston - Compressor Kit

Ring - Piston - Compressor KitFeaturesFine-tooth ratcheting motion will compress the bands in small increments for accurate compressionWill not break or damage ringsMade in the U.S.A.Specs

Jims #913 - Support Plate - Wheel Bearing Puller/Hub Protector

Support Plate - Wheel Bearing Puller/Hub ProtectorFeaturesUses two of the rotor mounts to give a strong, stable surface for bearing puller to work without damaging the hub's finishProvides accurate...

Jims #915 - Installation Inner Ball Bearing Tool

Installation Inner Ball Bearing ToolFeaturesAccurately and safely install the inner balancer bearing mounted in the left engine caseAll done on a work bench without using an arbor pressDesigned for...

Jims #917 - Clip - Pushrod Cover

Clip - Pushrod CoverFeaturesWill install and remove the clip professionally with just one hand in secondsThis tool will NOT marr or slipMade in the U.S.A.SpecsApplication

Jims #933 - Thread Chaser - SAE

Thread Chaser - SAEFeaturesAn inexpensive way to clean up threads on frames or other parts that have been powder-coated or paintedIncludes coarse sizes; 1/4"-20, 5/16"-18, 3/8"-16, 7/16"-14, 1/2"-13,...

Jims #937 - Valve Guide Remover - 7 mm

Valve Guide Remover - 7 mmFeaturesAvailable from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve sealsMade in the U.S.A.SpecsProduct Name

Jims #938 - Valve Guide Installer - 7 mm

Valve Guide Installer - 7 mmFeaturesAvailable from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve sealsMade in the U.S.A.SpecsApplication