Tools

Jims #939 - Tool - Wheel Bearing/Removal/Installation - Kit

Tool - Wheel Bearing/Removal/Installation - KitFeaturesRemoves and installs 3/4", 1" and 25 mm wheel bearing with or without ABSMade in the USASpecsProduct NameTool

Jims #941 - Oil Filter Tool - Slim

Oil Filter Tool - SlimFeaturesAn exclusive design makes it much easier to navigate when working near both the oil cooler and the crankcase position sensorAllows you more room to work around exhaust...

Jims #943 - Tool - Ignition Switch/Housing Alignment - '02-'13 Harley-Davidson

Tool - Ignition Switch/Housing Alignment - '02-'13 Harley-DavidsonFeaturesAlign ignition switch housing as retaining screws are being torquedAlso used to position switch in the correct orientation...

Jims #944 - Tool - Ignition Switch/Housing Alignment - '14-'17 Harley-Davidson

Tool - Ignition Switch/Housing Alignment - '14-'17 Harley-DavidsonFeaturesAlign ignition switch housing as retaining screws are being torquedAlso used to position switch in the correct orientation...

Jims #94547-80A - Sprocket Shaft Bearing Race Tool

Sprocket Shaft Bearing Race ToolFeaturesMust use with JIMS® Race and Bearing Install Handle (PART# DS-196042)Used to remove and install Timken® bearing race on motor casesMade in the U.S.A.Specs

Jims #94547-80B - Sprocket Shaft Bearing Race Tool

Sprocket Shaft Bearing Race ToolFeaturesMust use with JIMS® Race and Bearing Install Handle (PART# DS-196042)Used to remove and install Timken® bearing race on motor casesMade in the U.S.A.Specs

Jims #94555-55A - Pinion Nut Socket - Big Twin

Pinion Nut Socket - Big TwinFeaturesUse to remove or secure pinion gear nut to pinion gear shaftMade in the U.S.A.SpecsProduct NameNut

Jims #94630-67 - Jims Wheel Hub Nut Wrench Tool

Jims Wheel Hub Nut Wrench Tool

Jims #947 - Jims Rear Wheel Compensator Bearing Tool

Jims Rear Wheel Compensator Bearing Tool

Jims #94804-57 - Rocker Bush Remover - Twin Cam

Rocker Bush Remover - Twin CamFeaturesUse to ream rocker bushings to a factory fit of .0007” - .0012” in line with each otherThis precise line reamer is capable of a 24 finish or betterMade in the U...

Jims #951 - Jims Cylinder Torque Plate

Jims Cylinder Torque Plate

Jims #952 - Balancer Shift Alignment Tool

Balancer Shift Alignment ToolFeaturesTakes the guesswork out of setting up your balancer shaft sprocket and chain alignmentMade in the U.S.A.SpecsTypeBalancer Shaft

Jims #954 - Removal Tool - Fuel Pump/Retaining Ring - '08-'13 FL

Removal Tool - Fuel Pump/Retaining Ring - '08-'13 FLFeaturesUse for quick and easy service of fuel filter and other fuel-related partsRemoves/installs retaining ring holding fuel pumpHeavy-duty...

Jims #955 - Diagnostic Tool - Fuel Pressure/Fuel Injection

Diagnostic Tool - Fuel Pressure/Fuel InjectionFeaturesAccurately diagnose causes of stalling, poor fuel economy, loss of power, hesitation, fuel pump-related problems inside the tank and moreFuel...

Jims #956 - Replacement Sleeve - Timken Case Bearing Tool - Kit

Replacement Sleeve - Timken Case Bearing Tool - KitFeaturesSleeve is several times stronger than stock aluminum case material that standard bearings ride inReplacement sleeve kit for Timken® Case...