Tools

Jims #5804 - Adapter - Clutch Spring Compressor - Victory

Adapter - Clutch Spring Compressor - VictoryFeaturesMade in the USATo be used with clutch spring compressor Part# DS-197060.SpecsRiding StyleStreet

Jims #5805 - Wrist Pin Remover Tool - M8

Wrist Pin Remover Tool - M8FeaturesQuickly and easily removes wrist pins from Milwaukee-Eight® enginesAdapter part for JIMS® Wrist Pin Tool (PART# DS-196197)Made in the U.S.A.Specs

Jims #5806 - Camshaft Bearing - Remover/Installer Tool - M8

Camshaft Bearing - Remover/Installer Tool - M8FeaturesThe Milwaukee-Eight® engine returns to the single camshaft design, which requires a new tool for correct and accurate replacement of the camshaft...

Jims #5808 - Valve Spring Compression Collar Tool - M8

Valve Spring Compression Collar Tool - M8FeaturesValve spring collar allows existing compressor to remove smaller valves on M8 enginesFor use with JIMS® Valve Spring Compressor Tool (PART#...

Jims #5809 - Cylinder Hold Down Tool - M8

Cylinder Hold Down Tool - M8FeaturesUseful when installing the second cylinder over the piston and rings after the first cylinder has been installedOne end fits Twin Cam models, while the other end...

Jims #5810 - Main Seal Installer Tool - Left - M8

Main Seal Installer Tool - Left - M8FeaturesFor use on Milwaukee Eight series enginesSpecsUnitsEachRiding

Jims #5811 - Balancer Scissor Gear Tool - M8

Balancer Scissor Gear Tool - M8FeaturesHolds 2 halves of spring-loaded balancer scissor gear in alignment before removalBright color reminds technician to remove it before sealing engine caseFor use...

Jims #5812 - Rotor Alternator Tool - M8

Rotor Alternator Tool - M8FeaturesFor use on the Milwaukee Eight™ engine seriesRemoves rotor while protecting magnetsMade in the U.S.A.SpecsColor/FinishBlue

Jims #5813 - Main Bearing Remover and Installer Tool - M8

Main Bearing Remover and Installer Tool - M8FeaturesNot only removes the left and right main bearing without damaging the case, it also provides correct alignment and depth during installationHigh...

Jims #5813-5 - Stator Adapter Tool - M8

Stator Adapter Tool - M8FeaturesWhen this adapter is used in conjunction with the main bearing tool, or OE tool, the stator can remain attached to the left side case during bearing installationThis...

Jims #5816 - Countershaft 1st Scissor Gear Alignment Tool - Cruise Drive

Countershaft 1st Scissor Gear Alignment Tool - Cruise DriveFeaturesEssential for installing countershaft 1st scissor gear in cruise drive transmissionsEnsures scissor gear teeth mesh correctly with...

Jims #5820 - Installation Guide Tool - Standard - Rear Axle

Installation Guide Tool - Standard - Rear AxleFeaturesAligns wheel with swingarm, caliper brackets, wheel hubs and spacersMade in the USAFor Big Twin models with hollow 1" (25 mm) standard axlesSpecs

Jims #5821 - Fork Cap Installer - 49 mm

Fork Cap Installer - 49 mmFeaturesUsed to install fork tube caps without removing the fork legs from the bikeMade in the U.S.A.SpecsRiding StyleStreet

Jims #5822 - Swing Arm Bearing Installer

Swing Arm Bearing InstallerFeaturesBoth drive side and brake side bearings, which are at different depths, can be easily and accurately installed with this tool kitJIMS® took it one step further and...

Jims #5823 - Flywheel Lock - Mighty Bite - Blue - M8

Flywheel Lock - Mighty Bite - Blue - M8FeaturesLocks flywheel in place when performing service work to the connecting rods or pistons with the cylinders off the engineInstalls the case in place of...