Tools & Hardware

Jims 94804-57 - Rocker Bush Remover - Twin Cam

Rocker Bushing Reaming Tool Use to ream rocker bushings to a factory fit of .0007” - .0012” in line with each other This precise line reamer is capable of a 24 finish or better Made in the U.S.A.

Jims 94805-57 - Pinion Bushing Line Reamer - Big Twin

Pinion Bushing Reaming Tool Kit Use on all Big Twin '54-'99 single cam only, (NOTE: Includes aftermarket motors, also XL '57 to early '84 idler gear bushing) Designed to line-ream pinion bushing in cam cover from right case race Made in the U.S.A.

Jims 950 - Axle Plug - Hollow

Hollow Axle Plug Tool Lube the o-ring ends of these tools and insert in left and right ends of axle Helps establish a center point during alignment Plug into left and right ends of axle Made in the U.S.A.

Jims 951 - Torque Plate - Twin Cam '99-'17 - Original Equipment

Cylinder Torque Plate Kit Torque plates must be used when boring or honing late-model aluminum cylinders Simulate running stress conditions Come with instructions Made in the U.S.A.

Jims 952 - Balancer Shift Alignment Tool

Balancer Shaft Sprocket Alignment Tool Takes the guesswork out of setting up your balancer shaft sprocket and chain alignment Made in the U.S.A.

Jims 954 - Pump Ring Tool - '08-'13 FL

Fuel Pump Retainer Remover Tool Use for quick and easy service of fuel filter and other fuel-related parts Removes/installs retaining ring holding fuel pump Heavy-duty construction Made in the U.S.A.

Jims 955 - Gauge for Harley-Davidson Injection Pressure

Professional Fuel Injection Pressure Test Tool Includes all necessary parts to diagnose Delphi fuel injection; a large gauge assembly, 8" hose, 2" hose, fuel tank connection hose, throttle body connection hose, overflow hose, tee fitting, valve...

Jims 95560-57 - Access Cover Tool - Transmission - Big Twin

Transmission Access Cover Puller Tool Use to remove transmission access covers, which are press-fit on two dowel pins Made in the U.S.A.

Jims 956 - Sleeve Kit

Replacement Sleeve Kit Sleeve is several times stronger than stock aluminum case material that standard bearings ride in Replacement sleeve kit for Timken® Case Bearing Tool

Jims 95660-77 - Seal Driver - 4-Speed - Big Twin

Optional Seal Driver Optional drivers used in conjunction with main shaft seal tool allow installation of seals

Jims 95660-85 - Seal Driver - Transmission Main - 5-Speed

Optional Seal Driver Optional drivers used in conjunction with main shaft seal tool allow installation of seals

Jims 957 - Shaft Bearing Remover/Installer Tool - Balancer

Outer Balancer Bearing Tool Also installs the new balancer bearing and counter balancer shaft on Twin Cam 96", 103" or 110" "B" Softail engines Complete kit safely removes and installs outer balancer bearing on the chain guide support plate Made in...

Jims 95724-57 - Tappet Guide Puller - Tool - XL

Tappet Guide Puller Tool Used to remove press-fit tappet guides from crankcase Made in the U.S.A.

Jims 95760-TB - Camshaft Bearing - Puller - Big Twin

Inner Cam Bearing Removal Tool Used to remove inner cam bearing without damaging the crankcase Tool is also designed to keep rollers from falling into the crankcase Comes with instructions Made in the U.S.A.

Jims 95760-TP - Pinion Bearing Puller - Big Twin

Pinion Bushing Puller Use to remove pinion bushing from cam cover in one easy operation Use with JIMS® Cam Cover Holder Made in the U.S.A.

Jims 95760-XL - Camshaft Bearing - Puller - XL

Inner Cam Bearing Removal Tool Used to remove inner cam bearing without damaging the crankcase Tool is also designed to keep rollers from falling into the crankcase Comes with instructions Made in the U.S.A.

Jims 959 - Case Bearing Tool - Conversion - Twin Cam

Timken® Case Bearing Tool Kit Includes one new steel bearing insert sleeve (held to under .0002" total indicator reading), all necessary drill bits to drill oil feed and return holes, press plate that holds bearing sleeve insert in line with case...

Jims 95970-32C - Piston Pin Bush Tool

Piston Pin Bushing Tool Use to remove and install wrist pin bushings without removing rods from crankcase Made in the U.S.A.

Jims 960 - Balance Shaft Tool - Softail

Balancer Shaft Removal Tool Removes both the front and rear counter-balancer shaft bearing assembly, from the left engine case Designed for the 96" and 110" Beta® engines Made in the U.S.A.

Jims 963 - Bearing Puller Tool - '03-'17 Twin Cam

Bearing and Race Puller Tool Can also be used to remove Timken® bearing pinion shaft inner bearing race on '57-'07 XL, including all Buells®, and used to remove press-fit transmission gears and bearings from input and output shafts on all '02-'07 V-Rod...

Jims 96384-39 - Shift Fork Gauge - Big Twin

Shift Fork Gauge This tool checks alignment of Big Twin transmission shift forks Made in the U.S.A.

Jims 96385-78A - Shift Fork Gauge - 4-Speed - Big Twin

Shift Fork Gauge This tool checks alignment of Big Twin transmission shift forks Made in the U.S.A.

Jims 966 - Starter Seal Tool

Starter Jackshaft Seal Installer Tool Easily aligns and installs starter jackshaft seal without distorting or damaging seal Seal is located in upper part of inner primary of Big Twins Made in the U.S.A.

Jims 96600-36B - Valve Spring Compressor Tool - Harley-Davidson®

Valve Spring Compressor Tool Comes with new valve collar receiver for safer tool usage, and can be clamped in vice Hardened ball bearing style tip at valve head end eliminates damage to valve This tool is necessary for removing or installing valves ...