Tools & Hardware

Jims 908 - Feeler Gauge - Set

Feeler Gauge Set Tool includes two gauge holders and the following size gauge inserts: .002", .003", .004", .005", .006", .008", .009", .010" and .011" New innovative feeler gauge holder cures the need to use bulky multi-feeler gauge tools while...

Jims 910 - Ring - Piston - Compressor Kit

Piston Ring Compressor Set Fine-tooth ratcheting motion will compress the bands in small increments for accurate compression Will not break or damage rings Made in the U.S.A.

Jims 911 - Trap Door Bearing Remover/Installer - Cruise Drive/6-Speed - Harley Davidson

Harley Davidson Cruise Drive Trap Door Bearing Remover and Installer Accurately installs and removes lubed ball bearing into transmission trap door No arbor press needed Made in the U.S.A.

Jims 913 - Wheel Bearing Support Plate Tool

Late Model Wheel Bearing Tool Support Plate Provides accurate and precise bearing removal and installation without the risk of damage to cast wheels Attaches to the brake rotor mounting holes Works on 5 or 7 lug wheel Made in the U.S.A.

Jims 915 - Installation Inner Ball Bearing Tool

Balancer Inner Bearing Installer Accurately and safely install the inner balancer bearing mounted in the left engine case All done on a work bench without using an arbor press Designed for early or late Beta® cases Made in the U.S.A.

Jims 916 - Case Support Blocks

Twin Cam "B" Motor Case Support Blocks Aluminum blocks have inserted Delrin® pads that rest against case to prevent marring and to support the case Keeps case level when using bearing pullers to remove balancer inner bearings Protects left engine case...

Jims 917 - Clip - Pushrod Cover

Pushrod Cover Clip Will install and remove the clip professionally with just one hand in seconds This tool will NOT marr or slip Made in the U.S.A.

Jims 933 - Thread Chaser - SAE

Thread Chaser Tap Set An inexpensive way to clean up threads on frames or other parts that have been powder-coated or painted Includes coarse sizes; 1/4"-20, 5/16"-18, 3/8"-16, 7/16"-14, 1/2"-13, and 9/16"-12 Not for cutting new threads Made in the U...

Jims 937 - Valve Guide Remover - 7 mm

Shoulderless Valve Guide Tool Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A.

Jims 938 - Valve Guide Installer - 7 mm

Shoulderless Valve Guide Tool Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A.

Jims 939 - Sealed Wheel Bearing Tool

Sealed Wheel Bearing Kit Removes and installs 3/4", 1" and 25 mm wheel bearing with or without Anti-Locking Brake System (ABS) Made in the U.S.A.

Jims 941 - Oil Filter Tool - Slim

Slim Oil Filter Wrench An exclusive design makes it much easier to navigate when working near both the oil cooler and the crankcase position sensor Allows you more room to work around exhaust pipes, frame, hoses and brackets Simply the slimmest oil...

Jims 943 - Ignition Switch Alignment Tool

Ignition Switch Housing Alignment Tools Also used to position switch in the correct orientation for properly activating the fork lock Proper alignment of the switch will extend the life of the ignition switch housing Align ignition switch housing as...

Jims 944 - Ignition Switch Alignment Tool

Ignition Switch Housing Alignment Tools Also used to position switch in the correct orientation for properly activating the fork lock Proper alignment of the switch will extend the life of the ignition switch housing Align ignition switch housing as...

Jims 94547-80A - Sprocket Shaft Bearing Race Tool

Sprocket Shaft Bearing Race Tool Must use with JIMS® Race and Bearing Install Handle (PART# DS-196042) Used to remove and install Timken® bearing race on motor cases Made in the U.S.A.

Jims 94555-55A - Pinion Nut Socket - Big Twin

Pinion Gear Nut Socket Use to remove or secure pinion gear nut to pinion gear shaft Made in the U.S.A.

Jims 94804-57 - Rocker Bush Remover - Twin Cam

Rocker Bushing Reaming Tool Use to ream rocker bushings to a factory fit of .0007” - .0012” in line with each other This precise line reamer is capable of a 24 finish or better Made in the U.S.A.

Jims 952 - Balancer Shift Alignment Tool

Balancer Shaft Sprocket Alignment Tool Takes the guesswork out of setting up your balancer shaft sprocket and chain alignment Made in the U.S.A.

Jims 954 - Pump Ring Tool - '08-'13 FL

Fuel Pump Retainer Remover Tool Use for quick and easy service of fuel filter and other fuel-related parts Removes/installs retaining ring holding fuel pump Heavy-duty construction Made in the U.S.A.

Jims 955 - Gauge for Harley-Davidson Injection Pressure

Professional Fuel Injection Pressure Test Tool Includes all necessary parts to diagnose Delphi fuel injection; a large gauge assembly, 8" hose, 2" hose, fuel tank connection hose, throttle body connection hose, overflow hose, tee fitting, valve...

Jims 956 - Sleeve Kit

Replacement Sleeve Kit Sleeve is several times stronger than stock aluminum case material that standard bearings ride in Replacement sleeve kit for Timken® Case Bearing Tool

Jims 95660-77 - Seal Driver - 4-Speed - Big Twin

Optional Seal Driver Optional drivers used in conjunction with main shaft seal tool allow installation of seals

Jims 95660-85 - Seal Driver - Transmission Main - 5-Speed

Optional Seal Driver Optional drivers used in conjunction with main shaft seal tool allow installation of seals

Jims 95760-TB - Camshaft Bearing - Puller - Big Twin

Inner Cam Bearing Removal Tool Used to remove inner cam bearing without damaging the crankcase Tool is also designed to keep rollers from falling into the crankcase Comes with instructions Made in the U.S.A.