Tools & Hardware

Jims 95760-TP - Pinion Bearing Puller - Big Twin

Pinion Bushing Puller Use to remove pinion bushing from cam cover in one easy operation Use with JIMS® Cam Cover Holder Made in the U.S.A.

Jims 959 - Case Bearing Tool - Conversion - Twin Cam

Timken® Case Bearing Tool Kit Includes one new steel bearing insert sleeve (held to under .0002" total indicator reading), all necessary drill bits to drill oil feed and return holes, press plate that holds bearing sleeve insert in line with case...

Jims 95970-32C - Piston Pin Bush Tool

Piston Pin Bushing Tool Use to remove and install wrist pin bushings without removing rods from crankcase Made in the U.S.A.

Jims 960 - Balance Shaft Tool - Softail

Balancer Shaft Removal Tool Removes both the front and rear counter-balancer shaft bearing assembly, from the left engine case Designed for the 96" and 110" Beta® engines Made in the U.S.A.

Jims 96384-39 - Shift Fork Gauge - Big Twin

Shift Fork Gauge This tool checks alignment of Big Twin transmission shift forks Made in the U.S.A.

Jims 96385-78A - Shift Fork Gauge - 4-Speed - Big Twin

Shift Fork Gauge This tool checks alignment of Big Twin transmission shift forks Made in the U.S.A.

Jims 966 - Starter Seal Tool

Starter Jackshaft Seal Installer Tool Easily aligns and installs starter jackshaft seal without distorting or damaging seal Seal is located in upper part of inner primary of Big Twins Made in the U.S.A.

Jims 96600-36B - Valve Spring Compressor Tool - Harley-Davidson®

Valve Spring Compressor Tool Comes with new valve collar receiver for safer tool usage, and can be clamped in vice Hardened ball bearing style tip at valve head end eliminates damage to valve This tool is necessary for removing or installing valves ...

Jims 967 - Inner Primary Bearing/Seal Tool - Installation/Removal - Kit

Inner Primary Bearing and Seal Remover/Installer Tool — Removal/Installation Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer perimeter of bearing Also removes and installs inner primary bearing...

Jims 967-4 - Inner Primary Bearing Tool - Installation/Removal

Inner Primary Bearing and Seal Remover/Installer Tool — Removal/Installation Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer perimeter of bearing Also removes and installs inner primary bearing...

Jims 967-5 - Inner Primary Bearing Tool - Removal

Inner Primary Bearing and Seal Remover/Installer Tool — Removal Safely removes and installs inner primary bearing without any damage to new bearing by pushing on outer perimeter of bearing Also removes and installs inner primary bearing and seal that...

Jims 96780-32A - Piston Pin Keeper Tool

Piston Pin Keeper Tool This tool will install “Round Circlip” rings in one easy step without distorting ring, for the safest wrist pin retention possible Use to install retaining ring in piston Made in the U.S.A.

Jims 96780-58A - Piston Pin Lock Ring Tool - Big Twin

Piston Pin Lock Ring Tool Use to install lock ring (Harley-Davidson® No. 22582-52) in piston having .515” inner diameter wrist pins, like most aftermarket pistons This tool will install “spiral lock” rings in one easy step without distorting ring, for...

Jims 96830-51 - Pinion Gear Puller - Evolution/Shovelhead

Pinion Gear Puller Use to install pressed on splined pinion gears on Harley-Davidson® Big Twin Also can be used to remove pinion gear on Big Twin's and Sportsters Made in the U.S.A.

Jims 969 - O² Sensor Tool - Socket

O² Sensor Tool Remove and install oxygen sensors on fuel-injected models Socket tool will withstand up to 125 ft.-lbs. of torque Made in the USA

Jims 970 - Axle Locker Tool - 3rd Hand

3rd Hand Axle Locker Tool Eliminates the need for a helper or trying to blindly hold the axle from the other side of the tire Prevents axle from moving while torquing down the axle nut after setting belt tension Made in the U.S.A.

Jims 972 - Gear Seal Installer - Main Drive - 6-Speed

Driver Handle Use to install main drive gear oil seal to the proper depth with transmission assembled Includes protective sleeve for seal, which can be used to protect main drive gear inner bearings during installation Made in the U.S.A.

Jims 97273-60 - Camshaft Bearing Tool - XL

Inner Cam Bearing Install Tool Use to install inner cam bearings Made in the U.S.A.

Jims 973 - Sprocket Bearing Installer Tool

Bearing Adapter Allows installation of shaft bearing on '06 Harley-Davidson® Dyna Glide and all '07-'17 Twin Cam models An adapter for JIMS® Sprocket Shaft Bearing Tool

Jims 976 - Rotator Tool - Engine - Big Twin

Engine Rotator Rotates flywheel/piston assembly with engine still in frame or on a bench The perfect tool when doing pushrod adjustments, building big-inch engines and checking operating clearances Also can be used to keep the flywheel assembly from...

Jims 977 - Wrench - Fork Stem Nut

Fork Stem Nut Wrench This tool allows the ability to loosen, tighten and torque to spec the 1-1/2” stem nut without radio removal Normally to get access to the top stem nut requires the need to remove the radio package Saves up to 45 minutes for an...

Jims 981 - Main Drive Gear Tool - Cruise Drive/6-Speed

Harley Davidson Cruise Drive 6-Speed Main Drive Gear Installer Tool Holds the main drive gear square to its bearing bore, eliminating any marring of gear or bearings Installs the main drive gear without removing the transmission Made in the USA

Jims 984 - Transmission Door Tool - Big Twin

Transmission Door Puller Removes transmission door with gears and shaft attached Puller will not damage door bearings Made in the U.S.A.

Jims 985 - Shift Shaft Tool - Big Twin

Shifter Shaft Removal Tool Loosens and removes both shifter shafts from transmission door, allowing further disassembly of transmission Made in the U.S.A.