Tools

Jims #1075 - Installer - Cylinder Stud

Installer - Cylinder StudFeaturesAssembly tool features a captive hardened ball bearing dimensionally set 1" from top of toolWorks on all Evolution Big Twin and XL modelsMade in the U.S.A.Specs

Jims #1090 - Tester - Valve Spring

Tester - Valve SpringFeaturesTool fits any dual rate or conical valve spring with an O.D. no larger then 1.6” diameterWorks with bench vise, arbor, screw hydraulic or drill press0 to 1000 P.S.I...

Jims #1111 - Camshaft Pinion Gauge Pins 108

Camshaft Pinion Gauge Pins 108FeaturesUse to check pinion gear for pitch diametersCheck service manual for sizing chartMade in the U.S.A.SpecsGauge0.108"<

Jims #1133 - 7mm Valve Guide Ream Tool

7mm Valve Guide Ream Tool

Jims #1134 - Jims Rolling Buddy Engine Dummy Plate

Jims Rolling Buddy Engine Dummy Plate

Jims #1146 - Bearing Tool - Cam Side/Crankshaft - Installer/Remover - Twin Cam

Bearing Tool - Cam Side/Crankshaft - Installer/Remover - Twin CamFeaturesDesigned to protect engine cases by using a specially-designed support block to remove or install cam side crankshaft...

Jims #1147 - Alternator Rotor Puller

Alternator Rotor PullerFeaturesA must-have tool for 45A charging systems; will also work on any Harley-Davidson® alternator system that has threaded puller holesTool protects threads on sprocket...

Jims #1148 - Rod Alignment Tool - Twin Cam

Rod Alignment Tool - Twin CamFeaturesUse to check rod straightness without removing the rods from the casesMade in the U.S.A.SpecsOutside Diameter0.927"

Jims #1163 - Ball Shaft Retention Pins

Ball Shaft Retention PinsFeaturesLock into balancer shaft sprocket pinholes to prevent balancer from turning out of sync with flywheelUse to secure balancers when servicing the flywheel assemblyMade...

Jims #1164 - Pistons Support Plate

Pistons Support PlateFeaturesSupport plate gives a non-marring, flat surface to push piston bottoms against when installing rings or cylindersMade in the U.S.A.SpecsApplicationCy

Jims #1167 - Bearing Tool - Balancer Shaft/Removal - '00-'06 Softail

Bearing Tool - Balancer Shaft/Removal - '00-'06 SoftailFeaturesInstalling portion is designed to push on the outer diameter of bearings preventing any damage to the bearing or it's borePulls the...

Jims #1168 - Inspection Plug Tool - Primary Cover

Inspection Plug Tool - Primary CoverFeaturesUse this tool to remove and install primary inspection plugMade in the USASpecsRiding StyleStreet

Jims #1169 - Compression Release Guide - Twin Cam

Compression Release Guide - Twin CamFeaturesInstallation kit includes fixture, drill bit, spot face bit and thread-tapping toolSimply drill, spot face, tap and install compression release valvesWorks...

Jims #1236 - Ring - Piston - Compressor Kit

Ring - Piston - Compressor KitFeaturesFine-tooth ratcheting motion will compress the bands in small increments for accurate compressionWill not break or damage ringsMade in the U.S.A.Specs

Jims #1275 - Crankshaft Bearing Tool - Twin Cam

Crankshaft Bearing Tool - Twin CamFeaturesDesigned to remove and replace the right crankcase bearingPress bearing in and out straight with no damage to the caseMade in the U.S.A.Specs