Tools

Jims #1276 - Pin Remover - Wrist

Pin Remover - WristFeaturesCan be used easily by one person, no need to get another technician to hold the piston while drifting the pin in or outThis new JIMS® tool will cut the time it takes to...

Jims #1277 - Camshaft Remover and Installer

Camshaft Remover and InstallerFeaturesThis multi-function tool will remove and replace front and rear camshafts and the ball bearings in the Twin Cam 88It provides the precision alignment of the...

Jims #1278-3 - Camshaft Bearing Installation

Camshaft Bearing InstallationFeaturesReplacement drive for JIMS® Cam Bearing Installation ToolSpecsStyleReplacement

Jims #1279 - Inner Camshaft Bearing

Inner Camshaft BearingFeaturesUsed to remove inner cam bearing without damaging the crankcaseTool is also designed to keep rollers from falling into the crankcaseComes with instructionsMade in the U...

Jims #1280 - Camshaft Bearing Puller - Twin Cam

Camshaft Bearing Puller - Twin CamFeaturesOnce the camshafts are removed from the support plate this tool will remove the bearing from the camshaftRemoves bearing straight without binding or...

Jims #1283 - Camshaft Chain Tensioner Tool

Camshaft Chain Tensioner ToolFeaturesDesigned to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble camsAlso checks spring loads on chain tensionersComes...

Jims #1284 - Holding Tool - Connecting Rod - V-Twin

Holding Tool - Connecting Rod - V-TwinFeaturesHolds the rods in place when reaming or honing the wrist pin bushingsMade in the USAFor most V-Twin and Buell Blast applications.Specs

Jims #1285 - Cam/Crank Lock Tool - Sprocket

Cam/Crank Lock Tool - SprocketFeaturesDesigned to lock the camshafts and crankshaft sprockets when removing, replacing and torquing the sprocket boltsComes with instructionsMade in the U.S.A.Specs

Jims #1288 - Crankshaft Guide - '99-'17 Twin Cam

Crankshaft Guide - '99-'17 Twin CamFeaturesSpreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel assemblyMade in the U.S.A.SpecsUnitsEach

Jims #1290 - Jims Cam Gear Alignment Tool

Jims Cam Gear Alignment Tool

Jims #1457 - Jims Center Case Bolt Oversize

Jims Center Case Bolt Oversize

Jims #1658 - Shifter Shaft Sleeve Tool - Transmission - For 6-Speed

Shifter Shaft Sleeve Tool - Transmission - For 6-SpeedFeaturesCan be used to remove, install replacement or upgrade shifter shaft sleeve, assembly and drumUse to install shifter shaft sleeveMade in...

Jims #1664 - Shifter Shaft Sleeve Tool - Transmission - For 5-Speed

Shifter Shaft Sleeve Tool - Transmission - For 5-SpeedFeaturesCan be used to remove, install replacement or upgrade shifter shaft sleeve, assembly and drumUse to install shifter shaft sleeveMade in...

Jims #1665 - Pinion Gear Tool - XL

Pinion Gear Tool - XLFeaturesUse to lock pinion gear when torquing the pinion gear nutSimple to use; just align underneath gear and screw into caseMade in the U.S.A.SpecsProduct

Jims #1666 - Crank Lock Tool - XL

Crank Lock Tool - XLFeaturesUse to lock pinion gear when torquing the pinion gear nutSimple to use; just align underneath gear and screw into caseMade in the U.S.A.SpecsApplicati