Tools

Jims #1672 - Crankshaft Bearing Tool

Crankshaft Bearing ToolFeaturesDesigned to remove and replace the right crankcase bearingPress bearing in and out straight with no damage to the caseMade in the U.S.A.SpecsColor/

Jims #1700 - Main/Shaft Clutch Gear Tool

Main/Shaft Clutch Gear ToolFeaturesRemoves kick starter clutch gear successfully, without damage to the gearMade in the U.S.A.SpecsFor Engine Type4-Speed

Jims #1705 - Exhaust Drill Plate

Exhaust Drill PlateFeaturesWill position the seal evenly into the exhaust port of headTool can be used with exhaust flange nutsMade in the U.S.A.SpecsColor/FinishBlue

Jims #1706 - Jims Breather Ream Tool

Jims Breather Ream Tool

Jims #1707 - Cleveblock Spreading Tool

Cleveblock Spreading ToolFeaturesSpreads the swing arm cleveblocs allowing for installation of the swing armUse to install the swing arm in a 5-Speed rubber mount frameComes with instructionsMade in...

Jims #1720 - Main Bearing Remover - 5-Speed

Main Bearing Remover - 5-SpeedFeaturesRemoves old bearing straight and will not damage the transmission caseCan be used without removing transmission from the bikeMade in the U.S.A.Specs

Jims #1725 - Head Bearing Race Installer

Head Bearing Race InstallerFeaturesUse to install steering head races, stock and custom, as well as install cups in the frameThis tool pulls the races and cups in, straight and true, without any...

Jims #1726-1 - Bushing Reamer - Wrist Pin

Bushing Reamer - Wrist PinFeaturesSome wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications).Used to ream wrist pin bushings to the...

Jims #1726-2 - Bushing Reamer - Wrist Pin

Bushing Reamer - Wrist PinFeaturesSome wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications).Used to ream wrist pin bushings to the...

Jims #1726-3 - Bushing Reamer - Wrist Pin

Bushing Reamer - Wrist PinFeaturesSome wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications).Used to ream wrist pin bushings to the...

Jims #1743 - Swingarm Bushing Tool

Swingarm Bushing ToolFeaturesAllows installation of delicate, silicone cleveblock bushings in swingarm without damageTool presses on outer sleeve of bushingCan be used with or without a pressSpecs

Jims #1757 - Tool - O² Sensor/Spark Plug/Thread Chaser - M18 x 1.50

Tool - O² Sensor/Spark Plug/Thread Chaser - M18 x 1.50FeaturesDesigned with three flutes and a generous lead-in pilot for the best feel when repairing threadsUse to repair any I.D. thread that has...

Jims #1758 - Tool - O² Sensor/Spark Plug/Thread Chaser - M12 x 1.25

Tool - O² Sensor/Spark Plug/Thread Chaser - M12 x 1.25FeaturesDesigned with three flutes and a generous lead-in pilot for the best feel when repairing threadsUse to repair any I.D. thread that has...

Jims #1776 - Compressor Fork - Front

Compressor Fork - FrontFeaturesAlso includes FLT adapter for FLT forks to eliminate direct contact with spring coil and special rod to pull up fork damper rodTool compresses springs in...

Jims #2043 - Fork Nut Socket - 41 mm

Fork Nut Socket - 41 mmFeaturesEliminates possible burring of plug caused by wrenchesUsed to remove and install top fork-tube plugFits 41 mm forksMade in the U.S.A.Specs