Jims

Jims #5516 - Socket Tool - Sprocket Nut/Removal/Installation - Sportster

Socket Tool - Sprocket Nut/Removal/Installation - SportsterFeaturesEnsures the mainshaft on Harley-Davidson® Sportster models extends through the guidance collar for correct alignmentShort socket is...

Jims #5835 - Valve Spring Compressor Tool

Valve Spring Compressor ToolFeaturesOnce the cylinder is filled with compressed air, the technician can easily rotate the tool and compress the top collar of the valve spring exposing the keepers to...

Jims #5834 - Stand - Engine - M8 Softail

Stand - Engine - M8 SoftailFeaturesFor use on the Milwaukee Eight™ engine seriesJIMS Milwaukee-Eight® Softail® engine stand is designed to work on all Milwaukee-Eight® Softail enginesJIMS...

Jims #5832 - Ball Bearing Remover Tool

Ball Bearing Remover ToolFeaturesEasily remove the balancer bearings in both Touring and Softail models without damage to the crankcaseSpecsRiding StyleStreetUnitsEachProduct NameBalancer Bearing Tool

Jims #775 - Main Seal Tool - Removal/Installation - Twin Cam

Main Seal Tool - Removal/Installation - Twin CamFeaturesInstall and remove crank case main seal while the engine is still in the chassisIncludes necessary adapters for '88 and '96 Twin CamsMade in...

Jims #5532 - Tappet - Vacuum

Tappet - VacuumFeaturesRemoves the risk of using the starting system to pump up the lifters or damage to the valve train at low rpm if the lifters are not fully bledSpecial jar, designed for vacuum,...

Jims #5823 - Flywheel Lock - Mighty Bite - Blue - M8

Flywheel Lock - Mighty Bite - Blue - M8FeaturesLocks flywheel in place when performing service work to the connecting rods or pistons with the cylinders off the engineInstalls the case in place of...

Jims #5809 - Cylinder Hold Down Tool - M8

Cylinder Hold Down Tool - M8FeaturesUseful when installing the second cylinder over the piston and rings after the first cylinder has been installedOne end fits Twin Cam models, while the other end...

Jims #5805 - Wrist Pin Remover Tool - M8

Wrist Pin Remover Tool - M8FeaturesQuickly and easily removes wrist pins from Milwaukee-Eight® enginesAdapter part for JIMS® Wrist Pin Tool (PART# DS-196197)Made in the U.S.A...

Jims #2267 - Vise Stand - Cruise Drive

Vise Stand - Cruise DriveFeaturesAligns transmission gears and shafts for installationProtects parts from damage during installationAllows for quicker, safer and easier assemblyMade in the...

Jims #5504 - Tappet Position Holder

Tappet Position HolderFeaturesTappet locations are clearly referenced on the tool, which also serves to protect the tappets from damage when removed from the engineSafely stores anti-rotation pins...

Jims #1236 - Ring - Piston - Compressor Kit

Ring - Piston - Compressor KitFeaturesFine-tooth ratcheting motion will compress the bands in small increments for accurate compressionWill not break or damage ringsMade in the U.S.A...

Jims #5806 - Camshaft Bearing - Remover/Installer Tool - M8

Camshaft Bearing - Remover/Installer Tool - M8FeaturesThe Milwaukee-Eight® engine returns to the single camshaft design, which requires a new tool for correct and accurate replacement of the camshaft...

Jims #5812 - Rotor Alternator Tool - M8

Rotor Alternator Tool - M8FeaturesFor use on the Milwaukee Eight™ engine seriesRemoves rotor while protecting magnetsMade in the U.S.A.SpecsColor/FinishBlueRiding...

Jims #5810 - Main Seal Installer Tool - Left - M8

Main Seal Installer Tool - Left - M8FeaturesFor use on Milwaukee Eight series enginesSpecsUnitsEachRiding StyleStreetProduct NameSeal Installer

Jims #5826 - Stand - Engine - M8

Stand - Engine - M8FeaturesFor use on the Milwaukee Eight™ engine seriesJIMS Milwaukee-Eight® Softail® engine stand is designed to work on all Milwaukee-Eight® Softail enginesJIMS Milwaukee-Eight®...

Jims #5829 - Cylinder Torque Plates - M8

Cylinder Torque Plates - M8FeaturesTorque plates must be used when boring or honing late-model aluminum cylindersSimulate running stress conditionsCome with instructionsMade in the U.S.A...

Jims #5833 - Ball Bearing Installation Tool - M8

Ball Bearing Installation Tool - M8FeaturesAll Milwaukee-Eight® (M8) engines incorporate balancers to reduce vibrationDesigned to precisely install these bearings in the proper location for all M8...

Jims #5811 - Balancer Scissor Gear Tool - M8

Balancer Scissor Gear Tool - M8FeaturesHolds 2 halves of spring-loaded balancer scissor gear in alignment before removalBright color reminds technician to remove it before sealing engine caseFor use...

Jims #5800 - Flywheel Puller Tool - Indian

Flywheel Puller Tool - IndianFeaturesEliminates potential damage to the flywheel when used in this applicationEnsures good and solid engagement when using the pullerMade in the U.S.A.SpecsRiding...

Jims #5813 - Main Bearing Remover and Installer Tool - M8

Main Bearing Remover and Installer Tool - M8FeaturesNot only removes the left and right main bearing without damaging the case, it also provides correct alignment and depth during installationHigh...

Jims #5830 - Main Seal Remover Tool - Left

Main Seal Remover Tool - LeftFeaturesFor use on Milwaukee Eight series enginesSpecsRiding StyleStreetUnitsEachProduct NameSeal Remover

Jims #5808 - Valve Spring Compression Collar Tool - M8

Valve Spring Compression Collar Tool - M8FeaturesValve spring collar allows existing compressor to remove smaller valves on M8 enginesFor use with JIMS® Valve Spring Compressor Tool (PART#...

Jims #5828 - Cylinder Head Holder Tool - M8

Cylinder Head Holder Tool - M8FeaturesAllows you to easily position head for all types of workUse to hold head in vice through spark plug holeFor use with Milwaukee Eight engine seriesHas 14 mm and...