Jims

Jims 916 - Case Support Blocks

Twin Cam "B" Motor Case Support Blocks Aluminum blocks have inserted Delrin® pads that rest against case to prevent marring and to support the case Keeps case level when using bearing pullers to...

Jims #779 - Balancer Retainer Tool

Balancer Retainer ToolFeaturesHolds hydraulic tensioners in place that keep constant chain tension on counter balancer systemMade in the U.S.A.SpecsStyleHydraulicProduct NameTensioner HolderRiding...

Jims #993 - Inner Camshaft Bearing Tool

Inner Camshaft Bearing ToolFeaturesUsed to remove inner cam bearing without damaging the crankcaseTool is also designed to keep rollers from falling into the crankcaseComes with instructionsMade in...

Jims #2049 - Fork Seal Installation Tool - 49 mm

Fork Seal Installation Tool - 49 mmFeaturesInstalls lower leg 49 mm fork seals squarely into the bore without damaging the seal lip surfaceDesigned for specific Harley-Davidson® models except...

Jims #988 - Valve Spring - Compressor

Valve Spring - CompressorFeaturesUsed to remove and replace valve and new-style conical valve springRequires use of JIMS Valve Spring Compressor ToolMade in the U.S.A.SpecsProduct NameSpring...

Jims #966 - Starter Seal Tool

Starter Seal ToolFeaturesEasily aligns and installs starter jackshaft seal without distorting or damaging sealSeal is located in upper part of inner primary of Big TwinsMade in the U.S.A.SpecsProduct...

Jims #2312 - Primary Locking Bar Tool

Primary Locking Bar ToolFeaturesImmobilizes primary driveAllows for tightening with a torque wrench or loosening with a breaker barPrevents damage to rotor or magnets sometimes caused by...

Jims #1672 - Crankshaft Bearing Tool

Crankshaft Bearing ToolFeaturesDesigned to remove and replace the right crankcase bearingPress bearing in and out straight with no damage to the caseMade in the U.S.A...

Jims #956 - Replacement Sleeve - Timken Case Bearing Tool - Kit

Replacement Sleeve - Timken Case Bearing Tool - KitFeaturesSleeve is several times stronger than stock aluminum case material that standard bearings ride inReplacement sleeve kit for Timken® Case...

Jims #969 - O² Sensor Tool - Socket

O² Sensor Tool - SocketFeaturesRemove and install oxygen sensors on fuel-injected modelsSocket tool will withstand up to 125 ft.-lbs. of torqueMade in the USASpecsRiding StyleStreetUnitsEachDrive...

Jims #1075 - Installer - Cylinder Stud

Installer - Cylinder StudFeaturesAssembly tool features a captive hardened ball bearing dimensionally set 1" from top of toolWorks on all Evolution Big Twin and XL modelsMade in the U.S.A...

Jims #995 - Splitter Case - '07-'17 Twin Cam

Splitter Case - '07-'17 Twin CamFeatures"Breaks" the case sealant by pushing apart both case halvesUses included hand thread-in pushing screwFlywheels will be pushed from the left caseBolts...

Jims #1666 - Crank Lock Tool - XL

Crank Lock Tool - XLFeaturesUse to lock pinion gear when torquing the pinion gear nutSimple to use; just align underneath gear and screw into caseMade in the U.S.A.SpecsApplicationPinion...

Jims #994 - Camshaft Locking Tool - Big Twin

Camshaft Locking Tool - Big TwinFeaturesDesigned to lock the camshafts and crankshaft sprockets when removing, replacing and torquing the sprocket boltsComes with instructionsMade in the U.S.A...

Jims #1042-8 - Adapter - Wheel Bearing Puller - 25 mm

Adapter - Wheel Bearing Puller - 25 mmFeaturesMade in the USAFor use with 25 mm wheel bearing found on '07-'19 Harley-Davidson® models.SpecsColor/FinishBlackMeasurement SystemMetricTypeWheel...

Jims #972 - Gear Seal Installer - Main Drive - 6-Speed

Gear Seal Installer - Main Drive - 6-SpeedFeaturesUse to install main drive gear oil seal to the proper depth with transmission assembledIncludes protective sleeve for seal, which can be used to...

Jims #959 - Bearing Tool - Engine Case - Twin Cam

Bearing Tool - Engine Case - Twin CamFeaturesKit Includes one new steel bearing insert sleeve (held to under .0002" total indicator reading), all necessary drill bits to drill oil feed and...

Jims #960 - Balance Shaft Tool - Softail

Balance Shaft Tool - SoftailFeaturesRemoves both the front and rear counter-balancer shaft bearing assembly, from the left engine caseDesigned for the 96" and 110" Beta® enginesMade in the...

Jims #990 - Camshaft Assembly Tool - '07-'17 Twin Cam

Camshaft Assembly Tool - '07-'17 Twin CamFeaturesHolds both cams in an upright position while lowering cam support plate over both guides and cam journal guidesMade from a non-marring material that...

Jims #967 - Inner Primary Bearing/Seal Tool - Installation/Removal - Kit

Inner Primary Bearing/Seal Tool - Installation/Removal - KitFeaturesSafely removes and installs inner primary bearing without any damage to new bearing by pushing on outer perimeter of bearingAlso...

Jims #976 - Rotator Tool - Engine - Big Twin

Rotator Tool - Engine - Big TwinFeaturesRotates flywheel/piston assembly with engine still in frame or on a benchThe perfect tool when doing pushrod adjustments, building big-inch engines and...

Jims #973 - Sprocket Bearing Installer Tool

Sprocket Bearing Installer ToolFeaturesAllows installation of shaft bearing on '06 Harley-Davidson® Dyna Glide and all '07-'17 Twin Cam modelsAn adapter for JIMS® Sprocket Shaft Bearing...

Jims #5468 - Forceflow Cylinder Head Cooler Kit - Black - M8 Touring

Requires part # 0950-0605 for 110" motors.FeaturesIncludes Forceflow assembly with high-powered fan, OEM-type replacement horn, temperature switch, manual override switch, wiring, hardware and...

Jims #5401 - Forceflow Cylinder Head Cooler Kit - Black - Twin Cam Touring

Requires part # 0950-0605 for 110" motors.FeaturesIncludes Forceflow assembly with high-powered fan, OEM-type replacement horn, temperature switch, manual override switch, wiring, hardware and...