Jims

Jims 3200 - Gap Tool - Piston Ring End - Flange

Piston Ring End Gap Tool This tool makes measuring ring end gap faster, more accurate and eliminate the guess work Flanged design allows piston ring to fit squarely in cylinder bore every time ...

Jims 941 - Oil Filter Tool - Slim

Slim Oil Filter Wrench An exclusive design makes it much easier to navigate when working near both the oil cooler and the crankcase position sensor Allows you more room to work around exhaust...

Jims 910 - Ring - Piston - Compressor Kit

Piston Ring Compressor Set Fine-tooth ratcheting motion will compress the bands in small increments for accurate compression Will not break or damage rings Made in the U.S.A.

Jims 782 - Cylinder Leakdown - 4-Stroke

Dual Gauge Leakdown Tester Tool troubleshoots cylinder leakdown issues such as valve seat issues, bad rings and bad head gasket Hose assembly has both 14 mm and 18 mm spark plug threads Includes...

Jims 938 - Valve Guide Installer - 7 mm

Shoulderless Valve Guide Tool Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A.

Jims 917 - Clip - Pushrod Cover

Pushrod Cover Clip Will install and remove the clip professionally with just one hand in seconds This tool will NOT marr or slip Made in the U.S.A.

Jims 604 - Alignment Screws - Rocker Box

Rocker Box Alignment Screws Prevents misalignment of cover, compromising of seal and potential rocker interference Made in the U.S.A.

Jims 753 - Flywheel Lock with Tag - Mighty Bite - Blue - Twin Cam

Mighty Bite Flywheel Lock and Tag Locks flywheel in place when performing service work to the connecting rods or pistons with the cylinders off the engine For use on Twin Cam motors with crank...

Jims 916 - Case Support Blocks

Twin Cam "B" Motor Case Support Blocks Aluminum blocks have inserted Delrin® pads that rest against case to prevent marring and to support the case Keeps case level when using bearing pullers to...

Jims 779 - Balancer Retainer Tool

Hydraulic Balancer Retainer Tool Holds hydraulic tensioners in place that keep constant chain tension on counter balancer system Made in the U.S.A.

Jims 993 - Inner Camshaft Bearing Tool

Inner Cam Bearing Removal Tool Used to remove inner cam bearing without damaging the crankcase Tool is also designed to keep rollers from falling into the crankcase Comes with instructions Made...

Jims 2049 - Fork Seal Installation Tool - 49 mm

49mm Fork Seal and Dust Shield Installer Installs lower leg 49 mm fork seals squarely into the bore without damaging the seal lip surface Designed for specific Harley-Davidson® models except...

Jims 988 - Valve Spring - Compressor

Valve Spring Compressor Used to remove and replace valve and new-style conical valve spring Requires use of JIMS Valve Spring Compressor Tool Made in the U.S.A.

Jims 966 - Starter Seal Tool

Starter Jackshaft Seal Installer Tool Easily aligns and installs starter jackshaft seal without distorting or damaging seal Seal is located in upper part of inner primary of Big Twins Made in the...

Jims 2312 - Primary Locking Bar Tool

Primary Locking Bar Immobilizes primary drive Allows for tightening with a torque wrench or loosening with a breaker bar Prevents damage to rotor or magnets sometimes caused by air-wrench Made in...

Jims 1672 - Crankshaft Bearing Tool

Crankshaft Bearing Tool Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in the U.S.A.

Jims 956 - Sleeve Kit

Replacement Sleeve Kit Sleeve is several times stronger than stock aluminum case material that standard bearings ride in Replacement sleeve kit for Timken® Case Bearing Tool

Jims 969 - O² Sensor Tool - Socket

O² Sensor Tool Remove and install oxygen sensors on fuel-injected models Socket tool will withstand up to 125 ft.-lbs. of torque Made in the USA

Jims 1075 - Installer - Cylinder Stud

Evolution Cylinder Stud Assembly Tool Assembly tool features a captive hardened ball bearing dimensionally set 1" from top of tool Works on all Evolution Big Twin and XL models Made in the U.S.A.

Jims 995 - Splitter Case - '07-'17 Twin Cam

Case Splitter Tool "Breaks" the case sealant by pushing apart both case halves Uses included hand thread-in pushing screw Flywheels will be pushed from the left case Bolts to primary mounting...

Jims 1666 - Crank Lock Tool - XL

Pinion Gear Locker Tool Use to lock pinion gear when torquing the pinion gear nut Simple to use; just align underneath gear and screw into case Made in the U.S.A.

Jims 994 - Camshaft Locking Tool - Big Twin

Sprocket Lock Tool Designed to lock the camshafts and crankshaft sprockets when removing, replacing and torquing the sprocket bolts Comes with instructions Made in the U.S.A.

Jims 1042-8 - Wheel Bearing Puller Tool - 25 mm

25 mm Wheel Bearing Tool For use with 25 mm wheel bearing found on '07-'19 Harley-Davidson® models Made in the U.S.A.

Jims 972 - Gear Seal Installer - Main Drive - 6-Speed

Driver Handle Use to install main drive gear oil seal to the proper depth with transmission assembled Includes protective sleeve for seal, which can be used to protect main drive gear inner...