Jims

Jims #1163 - Ball Shaft Retention Pins

Ball Shaft Retention PinsFeaturesLock into balancer shaft sprocket pinholes to prevent balancer from turning out of sync with flywheelUse to secure balancers when servicing the flywheel assemblyMade...

Jims #1111 - Camshaft Pinion Gauge Pins 108

Camshaft Pinion Gauge Pins 108FeaturesUse to check pinion gear for pitch diametersCheck service manual for sizing chartMade in the U.S.A.SpecsGauge0.108"Measurement SystemSAETypePinion Gear...

Jims #1167 - Bearing Tool - Balancer Shaft/Removal - '00-'06 Softail

Bearing Tool - Balancer Shaft/Removal - '00-'06 SoftailFeaturesInstalling portion is designed to push on the outer diameter of bearings preventing any damage to the bearing or it's borePulls the...

Jims #1148 - Rod Alignment Tool - Twin Cam

Rod Alignment Tool - Twin CamFeaturesUse to check rod straightness without removing the rods from the casesMade in the U.S.A.SpecsOutside Diameter0.927"Riding StyleStreetOverall...

Jims #25586-37 - Cam Bushing - XL

Cam Bushing - XLFeaturesBushings are made from solid bronze bar stockMachined in one operation with a tolerance of .0002"Feature a lead-in for ease of installationMade in the U.S.A.SpecsTypeCam...

Jims #2244 - Fork Nut Socket - 35 mm - 3/8"

Fork Nut Socket - 35 mm - 3/8"FeaturesUsed to remove and install top fork nuts on fork tubesRubber protector inside socketWill clear most handlebarsMade in the U.S.A.SpecsTypeRemoval ToolFork...

Jims #1047-TP - Crank Assembly Removal Tool - '55+ Big Twin

Crank Assembly Removal Tool - '55+ Big TwinFeaturesThis tool can only be used for removing the flywheel from the left caseWill also press cases apart and break sealant bondSome case pressing will...

Jims #95660-42 - 4-Speed Transmission Main Seal Tool - '36-'76 Big Twin

4-Speed Transmission Main Seal Tool - '36-'76 Big TwinFeaturesUsed to remove and install the main drive seal on specific Harley-Davidson® Big Twin modelsMade in the U.S.A.SpecsProduct NameSeal...

Jims #1275 - Crankshaft Bearing Tool - Twin Cam

Crankshaft Bearing Tool - Twin CamFeaturesDesigned to remove and replace the right crankcase bearingPress bearing in and out straight with no damage to the caseMade in the U.S.A.SpecsRiding...

Jims #95760-TB - Camshaft Bearing - Puller - Big Twin

Camshaft Bearing - Puller - Big TwinFeaturesUsed to remove inner cam bearing without damaging the crankcaseTool is also designed to keep rollers from falling into the crankcaseComes with...

Jims #35316-80 - Main Drive Gear Tool - 5-Speed

Main Drive Gear Tool - 5-SpeedFeaturesInstalls the main drive gear without removing the transmissionUsed to remove and install the main drive gearMade in the USASpecsProduct NameMain Drive Gear...

Jims #94804-57 - Rocker Bush Remover - Twin Cam

Rocker Bush Remover - Twin CamFeaturesUse to ream rocker bushings to a factory fit of .0007” - .0012” in line with each otherThis precise line reamer is capable of a 24 finish or betterMade in the U...

Jims #1283 - Camshaft Chain Tensioner Tool

Camshaft Chain Tensioner ToolFeaturesDesigned to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble camsAlso checks spring loads on chain tensionersComes...

Jims #94547-80A - Sprocket Shaft Bearing Race Tool

Sprocket Shaft Bearing Race ToolFeaturesMust use with JIMS® Race and Bearing Install Handle (PART# DS-196042)Used to remove and install Timken® bearing race on motor casesMade in the U.S.A...

Jims #96385-78A - Shift Fork Gauge - 4-Speed - Big Twin

Shift Fork Gauge - 4-Speed - Big TwinFeaturesThis tool checks alignment of Big Twin transmission shift forksMade in the U.S.A.SpecsUnitsEachColor/FinishRedTypeFork AlignmentApplicationPlate-Type...