Tools & Hardware

Jims 1051 - Wrist Pin Bushing Tool

Connecting Rod Wrist Pin Bushing Tool Used to remove and install wrist pin bushings without removing connecting rods from crankcases Comes with instructions Made in the U.S.A.

Jims 1075 - Installer - Cylinder Stud

Evolution Cylinder Stud Assembly Tool Assembly tool features a captive hardened ball bearing dimensionally set 1" from top of tool Works on all Evolution Big Twin and XL models Made in the U.S.A.

Jims 1090 - Tester - Valve Spring

Mini Valve Spring Tester Tool fits any dual rate or conical valve spring with an O.D. no larger then 1.6” diameter Works with bench vise, arbor, screw hydraulic or drill press 0 to 1000 P.S.I. gauge Made in the U.S.A.

Jims 1111 - Camshaft Pinion Gauge Pins 108

Cam and Pinion Gear Gauge Pins Use to check pinion gear for pitch diameters Check service manual for sizing chart Made in the U.S.A.

Jims 1146 - Crankshaft Bearing Installer - Twin Cam

Twin Cam "B" Motor Crankshaft Bearing Tool Designed to protect engine cases by using a specially-designed support block to remove or install cam side crankshaft bearing Made in the U.S.A.

Jims 1148 - Rod Alignment Tool - Twin Cam

Rod Alignment Tool Use to check rod straightness without removing the rods from the cases Made in the U.S.A.

Jims 1162 - Caliper Piston Remover

Brake Caliper Piston Remover Prevents damage to pistons and cylinders when installing new seals and wipers Holds pistons square in their cylinder bores during removal Designed for front and rear 4-piston calipers Made in the U.S.A.

Jims 1163 - Ball Shaft Retention Pins

Balancer Shaft Retention Pins Lock into balancer shaft sprocket pinholes to prevent balancer from turning out of sync with flywheel Use to secure balancers when servicing the flywheel assembly Made in the U.S.A.

Jims 1167 - Balancing Shaft Bearing Tool

Balancer Shaft Bearing Remover Installing portion is designed to push on the outer diameter of bearings preventing any damage to the bearing or it's bore Pulls the bearings from the "B" motor case in one easy smooth motion preventing any damage to the...

Jims 1169 - Compression Release Guide - Twin Cam

Compression Release Valve Installation Kit Installation kit includes fixture, drill bit, spot face bit and thread-tapping tool Simply drill, spot face, tap and install compression release valves Works on front and back head, with or without valves...

Jims 1236 - Ring - Piston - Compressor Kit

Piston Ring Compressor Set Fine-tooth ratcheting motion will compress the bands in small increments for accurate compression Will not break or damage rings Made in the U.S.A.

Jims 1275 - Crankshaft Bearing Tool - Twin Cam

Crankshaft Bearing Tool Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in the U.S.A.

Jims 1276 - Pin Remover - Wrist

Wrist Pin Tool Can be used easily by one person, no need to get another technician to hold the piston while drifting the pin in or out This new JIMS® tool will cut the time it takes to remove and install wrist pins Made in the U.S.A.

Jims 1277 - Camshaft Remover and Installer

Camshaft Removal/Installation Tool This multi-function tool will remove and replace front and rear camshafts and the ball bearings in the Twin Cam 88 It provides the precision alignment of the camshaft to ensure a smooth press in and out of the support...

Jims 1278-3 - Camshaft Bearing Installation

Replacement Drive Replacement drive for JIMS® Cam Bearing Installation Tool

Jims 1279 - Inner Camshaft Bearing

Inner Cam Bearing Removal Tool Used to remove inner cam bearing without damaging the crankcase Tool is also designed to keep rollers from falling into the crankcase Comes with instructions Made in the U.S.A.

Jims 1280 - Camshaft Bearing Puller - Twin Cam

Cam Bearing Puller Once the camshafts are removed from the support plate this tool will remove the bearing from the camshaft Removes bearing straight without binding or slipping Made in the U.S.A.

Jims 1283 - Camshaft Chain Tensioner Tool

Cam Chain Tensioner Tool Designed to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams Also checks spring loads on chain tensioners Comes with instructions Made in the U.S.A.

Jims 1284 - Holding Tool - Connecting Rod - V-Twin

Rod Holder Tool Holds the rods in place when reaming or honing the wrist pin bushings Made in the USA For most V-Twin and Buell Blast applications.

Jims 1288 - Crankshaft Guide - '99-'17 Twin Cam

Crankshaft Guide Spreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel assembly Made in the U.S.A.

Jims 1658 - Shift Shaft Sleeve Tool

Shifter Shaft Sleeve Tool Can be used to remove, install replacement or upgrade shifter shaft sleeve, assembly and drum Use to install shifter shaft sleeve Made in the U.S.A.

Jims 1665 - Pinion Gear Tool - XL

Pinion Gear Locker Tool Use to lock pinion gear when torquing the pinion gear nut Simple to use; just align underneath gear and screw into case Made in the U.S.A.

Jims 1666 - Crank Lock Tool - XL

Pinion Gear Locker Tool Use to lock pinion gear when torquing the pinion gear nut Simple to use; just align underneath gear and screw into case Made in the U.S.A.

Jims 1672 - Crankshaft Bearing Tool

Crankshaft Bearing Tool Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in the U.S.A.