Tools & Hardware

Jims 1278-3 - Camshaft Bearing Installation

Replacement Drive Replacement drive for JIMS® Cam Bearing Installation Tool

Jims 1279 - Inner Camshaft Bearing

Inner Cam Bearing Removal Tool Used to remove inner cam bearing without damaging the crankcase Tool is also designed to keep rollers from falling into the crankcase Comes with instructions Made in the U.S.A.

Jims 1280 - Camshaft Bearing Puller - Twin Cam

Cam Bearing Puller Once the camshafts are removed from the support plate this tool will remove the bearing from the camshaft Removes bearing straight without binding or slipping Made in the U.S.A.

Jims 1283 - Camshaft Chain Tensioner Tool

Cam Chain Tensioner Tool Designed to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams Also checks spring loads on chain tensioners Comes with instructions Made in the U.S.A.

Jims 1284 - Holding Tool - Connecting Rod - V-Twin

Rod Holder Tool Holds the rods in place when reaming or honing the wrist pin bushings Made in the USA For most V-Twin and Buell Blast applications.

Jims 1288 - Crankshaft Guide - '99-'17 Twin Cam

Crankshaft Guide Spreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel assembly Made in the U.S.A.

Jims 1658 - Shift Shaft Sleeve Tool

Shifter Shaft Sleeve Tool Can be used to remove, install replacement or upgrade shifter shaft sleeve, assembly and drum Use to install shifter shaft sleeve Made in the U.S.A.

Jims 1665 - Pinion Gear Tool - XL

Pinion Gear Locker Tool Use to lock pinion gear when torquing the pinion gear nut Simple to use; just align underneath gear and screw into case Made in the U.S.A.

Jims 1666 - Crank Lock Tool - XL

Pinion Gear Locker Tool Use to lock pinion gear when torquing the pinion gear nut Simple to use; just align underneath gear and screw into case Made in the U.S.A.

Jims 1672 - Crankshaft Bearing Tool

Crankshaft Bearing Tool Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in the U.S.A.

Jims 1705 - Exhaust Drill Plate

Exhaust Stud Drill Plate Will position the seal evenly into the exhaust port of head Tool can be used with exhaust flange nuts Made in the U.S.A.

Jims 1709 - Sprocket Shaft Bearing Tool - Big Twin

Sprocket Shaft Bearing Remover Tool is used to remove the sprocket shaft Timken® bearing on late '86-'02 Big Twins with an integral sprocket shaft Does the job better than anything else on the market Made in the U.S.A.

Jims 1710 - Outer Race Snap Ring

Snap Ring Tool Used for removing and installing the Timken® bearing outer race snap ring A must for replacing rings in OEM and aftermarket cases Made in the U.S.A.

Jims 1720 - Main Bearing Remover - 5-Speed

Main Drive Gear Bearing Removal Tool Removes old bearing straight and will not damage the transmission case Can be used without removing transmission from the bike Made in the U.S.A.

Jims 1726-1 - Bushing Reamer - Wrist Pin

Wrist Pin Bushing Reaming Tool Some wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications). Used to ream wrist pin bushings to the proper inner diameter Can be used with rods in or out...

Jims 1726-2 - Bushing Reamer - Wrist Pin

Wrist Pin Bushing Reaming Tool Some wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications). Used to ream wrist pin bushings to the proper inner diameter Can be used with rods in or out...

Jims 1726-3 - Bushing Reamer - Wrist Pin

Wrist Pin Bushing Reaming Tool Some wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications). Used to ream wrist pin bushings to the proper inner diameter Can be used with rods in or out...

Jims 1743 - Swingarm Bushing Tool

Swingarm Bushing Tool Allows installation of delicate, silicone cleveblock bushings in swingarm without damage Tool presses on outer sleeve of bushing Can be used with or without a press

Jims 1745 - Bearing Simulator - Big Twin

Timken® Bearing Simulator Designed to allow quick and easy removal and replacement of flywheel assembly in the left-side crankcase when checking rod-to-case, piston-to-flywheel or cylinder-to-flywheel clearance Will not mar bearing races Made in the U...

Jims 1776 - Compressor Fork - Front

Front Fork Compressor Tool Also includes FLT adapter for FLT forks to eliminate direct contact with spring coil and special rod to pull up fork damper rod Tool compresses springs in cartridge-style forks when servicing or rebuilding Can be mounted in...

Jims 1803 - Hydrosolid Tappet - XL

Hydrosolid Tappets Perform like a hydraulic tappet up to 5500 rpm, then turn into a solid tappet When they turn into solid tappets, it adds approximately three to six more usable horsepower Prevent hydraulic pump at high rpms Made in the U.S.A. ...

Jims 18526-PG - Tappet - Standard - XL

Big Axle™ Powerglide™ Tappets Micro-finish bore allows a running fit of .0002" Big Axle™ rollers are designed around three working parts The outer wheel/roller has a 27% greater wall size - less harmonic distortion for better tracking of cam lobe Pin...

Jims 2043 - Fork Nut Socket - 41 mm

Fork Nut Socket Eliminates possible burring of plug caused by wrenches Used to remove and install top fork-tube plug Fits 41 mm forks Made in the U.S.A.

Jims 2045 - Fork Seal Installer - 35 mm

Fork Seal and Cap Installer Lightly grease to keep from scratching fork tubes Used to install fork and dust seals Made in the U.S.A.