Tools & Hardware

Jims 2317 - Primary Locking Bar - 5-Speed

Primary Locking Bar Immobilizes primary drive Allows for tightening with a torque wrench or loosening with a breaker bar Prevents damage to rotor or magnets sometimes caused by air-wrench Made in the U.S.A.

Jims 2318 - Primary Locking Bar - XL

Primary Locking Bar Immobilizes primary drive Allows for tightening with a torque wrench or loosening with a breaker bar Prevents damage to rotor or magnets sometimes caused by air-wrench Made in the U.S.A.

Jims 2324 - Sprocket Shaft Installer

Sprocket Shaft Seal Installer Installs sprocket seal to proper depth Use with JIMS® Driver Handle Holds seal perfectly square Made in the U.S.A.

Jims 2388 - Driver Spacer Tool

Driver Spacer Tool Used with JIMS Bearing Race Tool to remove and install the steering head bearing race

Jims 2392 - Head Bolt - Torque Plate

Head Bolt Torque Gauge This accurate gauge allows the measuring of 90° when tightening head bolts Torquing sequence laser engraved on gauge, with instructions Works on all Twin Cam and Evolution engines Made in the U.S.A.

Jims 3200 - Gap Tool - Piston Ring End - Flange

Piston Ring End Gap Tool This tool makes measuring ring end gap faster, more accurate and eliminate the guess work Flanged design allows piston ring to fit squarely in cylinder bore every time Made in the USA For H-D 95", 103", and 110" motors w/...

Jims 33071-73 - Remover and Installer - Bearing Race

Wheel Bearing Race Tool Designed to remove and install bearing cups in cast wheels Use with JIMS® Handle

Jims 33119-79A - Shift Adjuster - 5-Speed

Shifter Arm Adjusting Screw High-quality OEM replacement component Made in the U.S.A.

Jims 33416-80 - Handle - Road and Race Tools

Race and Bearing Handle Tool Easy-to-use race installer/remover handle by JIMS® Use with JIMS® Bearing Race Tools Made in the U.S.A.

Jims 33443-84 - Tappet Aligning Tool - Big Twin

Tappet Block Alignment Tool Can also be used to align rocker box bases on Evolution head (requires two tools) Also used in Harley-Davidson® Twin Cam oil pump alignment applications Used to align oil hole from crankcase to tappet block Made in the U.S...

Jims 34623-83 - Piston Pin Tool - Evolution

Piston Pin Keeper Tool This tool will install “Round Circlip” rings in one easy step without distorting ring, for the safest wrist pin retention possible Use to install retaining ring in piston Made in the U.S.A.

Jims 34731-84 - Valve Guide Installer

Shoulderless Valve Guide Tool Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A.

Jims 34740-84 - Valve Guide Remover

Shoulderless Valve Guide Tool Available from JIMS to allow the proper removal or installation of shoulderless valve guides as well as valve seals Made in the U.S.A.

Jims 34902-84 - Mainshaft Bearing Race Tool - Big Twin

Mainshaft Bearing Race Tool Used to remove and install the inner bearing race on the transmission mainshaft Made in the U.S.A.

Jims 34902-84-3 - Puller Plate Tool

Replacement Puller Plate Replacement puller plate for Jim's Mainshaft Bearing Race Tool for Big Twin models Made in the U.S.A.

Jims 38515-90 - Clutch Spring Compressor

Clutch Spring Compressor Tool For '91-'03 XL applications, compressor nut must be used in conjunction with compressor tool Used to release clutch spring so retainer ring can be easily removed and installed Made in the U.S.A.

Jims 38515-91 - Nut Clutch Spring Compressor XL

Clutch Spring Compressor Tool For '91-'03 XL applications, compressor nut must be used in conjunction with compressor tool Used to release clutch spring so retainer ring can be easily removed and installed Made in the U.S.A.

Jims 39361-69 - Seal Installation Tool - Sprocket Shaft

Motor Sprocket Shaft Seal Install Tool Designed to press oil seal over sprocket shaft into case Made in the U.S.A.

Jims 5501 - Battery Lifter Tool

Battery Lifter Modeled after the larger tools made for automotive batteries, but is properly sized for Harley-Davidson® models Easily lifts batteries that have an extremely tight fit in the compartment Made in the U.S.A.

Jims 5502 - Ultimate Clutch Adjusting Tool

Ultimate Clutch Adjusting Tool Allows the quick and accurate tightening of the clutch adjusting screw jam nut without having the screw change position No more guessing or making multiple attempts to lock the nut and adjuster screw in the proper place ...

Jims 5503 - Master Kit - Front/Rear Brake/Clutch

Master Cylinder Hydraulic Brake Bleeding Solution Consists of a vacuum-bleed device with a transparent cap which forms a tight seal to the master cylinder and has a fitting to attach a vacuum pump Cleaner way to purge the system of air with less fluid...

Jims 5504 - Tappet Position Holder

Tappet Position Holding Tool Tappet locations are clearly referenced on the tool, which also serves to protect the tappets from damage when removed from the engine Safely stores anti-rotation pins and tappets for proper and accurate installation Made...

Jims 5506 - Magnetic Tappet Holder - Twin Cam and M8

Magnetic Tappet Holder Never turn the engine over if the tappet will not spin with your fingers after adjustments were made It is very important that the engine is not rotated while pushrods are tight The pushrod will spin with your fingers after the...

Jims 5507 - Lid Kit - Front Brake

Master Cylinder Brake Bleeding Solution Consists of a vacuum-bleed device with a transparent cap which forms a tight seal to the master cylinder and has a fitting to attach a vacuum pump Cleaner way to purge the system of air with less fluid used and a...