Tools & Hardware

Jims 1148 - Rod Alignment Tool - Twin Cam

Rod Alignment Tool Use to check rod straightness without removing the rods from the cases Made in the U.S.A.

Jims 1162 - Caliper Piston Remover

Brake Caliper Piston Remover Prevents damage to pistons and cylinders when installing new seals and wipers Holds pistons square in their cylinder bores during removal Designed for front and rear 4-piston calipers Made in the U.S.A.

Jims 1163 - Ball Shaft Retention Pins

Balancer Shaft Retention Pins Lock into balancer shaft sprocket pinholes to prevent balancer from turning out of sync with flywheel Use to secure balancers when servicing the flywheel assembly Made in the U.S.A.

Jims 1167 - Balancing Shaft Bearing Tool

Balancer Shaft Bearing Remover Installing portion is designed to push on the outer diameter of bearings preventing any damage to the bearing or it's bore Pulls the bearings from the "B" motor case in one easy smooth motion preventing any damage to the...

Jims 1169 - Compression Release Guide - Twin Cam

Compression Release Valve Installation Kit Installation kit includes fixture, drill bit, spot face bit and thread-tapping tool Simply drill, spot face, tap and install compression release valves Works on front and back head, with or without valves...

Jims 1236 - Ring - Piston - Compressor Kit

Piston Ring Compressor Set Fine-tooth ratcheting motion will compress the bands in small increments for accurate compression Will not break or damage rings Made in the U.S.A.

Jims 1275 - Crankshaft Bearing Tool - Twin Cam

Crankshaft Bearing Tool Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in the U.S.A.

Jims 1276 - Pin Remover - Wrist

Wrist Pin Tool Can be used easily by one person, no need to get another technician to hold the piston while drifting the pin in or out This new JIMS® tool will cut the time it takes to remove and install wrist pins Made in the U.S.A.

Jims 1277 - Camshaft Remover and Installer

Camshaft Removal/Installation Tool This multi-function tool will remove and replace front and rear camshafts and the ball bearings in the Twin Cam 88 It provides the precision alignment of the camshaft to ensure a smooth press in and out of the support...

Jims 1278-3 - Camshaft Bearing Installation

Replacement Drive Replacement drive for JIMS® Cam Bearing Installation Tool

Jims 1279 - Inner Camshaft Bearing

Inner Cam Bearing Removal Tool Used to remove inner cam bearing without damaging the crankcase Tool is also designed to keep rollers from falling into the crankcase Comes with instructions Made in the U.S.A.

Jims 1280 - Camshaft Bearing Puller - Twin Cam

Cam Bearing Puller Once the camshafts are removed from the support plate this tool will remove the bearing from the camshaft Removes bearing straight without binding or slipping Made in the U.S.A.

Jims 1283 - Camshaft Chain Tensioner Tool

Cam Chain Tensioner Tool Designed to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble cams Also checks spring loads on chain tensioners Comes with instructions Made in the U.S.A.

Jims 1284 - Holding Tool - Connecting Rod - V-Twin

Rod Holder Tool Holds the rods in place when reaming or honing the wrist pin bushings Made in the USA For most V-Twin and Buell Blast applications.

Jims 1288 - Crankshaft Guide - '99-'17 Twin Cam

Crankshaft Guide Spreads the crankcase pinion bearing rollers when reassembling right side case to the flywheel assembly Made in the U.S.A.

Jims 1658 - Shift Shaft Sleeve Tool

Shifter Shaft Sleeve Tool Can be used to remove, install replacement or upgrade shifter shaft sleeve, assembly and drum Use to install shifter shaft sleeve Made in the U.S.A.

Jims 1665 - Pinion Gear Tool - XL

Pinion Gear Locker Tool Use to lock pinion gear when torquing the pinion gear nut Simple to use; just align underneath gear and screw into case Made in the U.S.A.

Jims 1666 - Crank Lock Tool - XL

Pinion Gear Locker Tool Use to lock pinion gear when torquing the pinion gear nut Simple to use; just align underneath gear and screw into case Made in the U.S.A.

Jims 1672 - Crankshaft Bearing Tool

Crankshaft Bearing Tool Designed to remove and replace the right crankcase bearing Press bearing in and out straight with no damage to the case Made in the U.S.A.

Jims 1705 - Exhaust Drill Plate

Exhaust Stud Drill Plate Will position the seal evenly into the exhaust port of head Tool can be used with exhaust flange nuts Made in the U.S.A.

Jims 1709 - Sprocket Shaft Bearing Tool - Big Twin

Sprocket Shaft Bearing Remover Tool is used to remove the sprocket shaft Timken® bearing on late '86-'02 Big Twins with an integral sprocket shaft Does the job better than anything else on the market Made in the U.S.A.

Jims 1710 - Outer Race Snap Ring

Snap Ring Tool Used for removing and installing the Timken® bearing outer race snap ring A must for replacing rings in OEM and aftermarket cases Made in the U.S.A.

Jims 1720 - Main Bearing Remover - 5-Speed

Main Drive Gear Bearing Removal Tool Removes old bearing straight and will not damage the transmission case Can be used without removing transmission from the bike Made in the U.S.A.

Jims 1726-1 - Bushing Reamer - Wrist Pin

Wrist Pin Bushing Reaming Tool Some wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications). Used to ream wrist pin bushings to the proper inner diameter Can be used with rods in or out...