Jims

Jims #1047-TP - Crank Assembly Removal Tool - '55+ Big Twin

Crank Assembly Removal Tool - '55+ Big TwinFeaturesThis tool can only be used for removing the flywheel from the left caseWill also press cases apart and break sealant bondSome case pressing will...

Jims #95660-42 - 4-Speed Transmission Main Seal Tool - '36-'76 Big Twin

4-Speed Transmission Main Seal Tool - '36-'76 Big TwinFeaturesUsed to remove and install the main drive seal on specific Harley-Davidson® Big Twin modelsMade in the U.S.A.SpecsProduct NameSeal...

Jims #1275 - Crankshaft Bearing Tool - Twin Cam

Crankshaft Bearing Tool - Twin CamFeaturesDesigned to remove and replace the right crankcase bearingPress bearing in and out straight with no damage to the caseMade in the U.S.A.SpecsRiding...

Jims #95760-TB - Camshaft Bearing - Puller - Big Twin

Camshaft Bearing - Puller - Big TwinFeaturesUsed to remove inner cam bearing without damaging the crankcaseTool is also designed to keep rollers from falling into the crankcaseComes with...

Jims #35316-80 - Main Drive Gear Tool - 5-Speed

Main Drive Gear Tool - 5-SpeedFeaturesInstalls the main drive gear without removing the transmissionUsed to remove and install the main drive gearMade in the USASpecsProduct NameMain Drive Gear...

Jims #94804-57 - Rocker Bush Remover - Twin Cam

Rocker Bush Remover - Twin CamFeaturesUse to ream rocker bushings to a factory fit of .0007” - .0012” in line with each otherThis precise line reamer is capable of a 24 finish or betterMade in the U...

Jims #1283 - Camshaft Chain Tensioner Tool

Camshaft Chain Tensioner ToolFeaturesDesigned to unload the pressure on the primary and secondary chain tensioners to assemble and disassemble camsAlso checks spring loads on chain tensionersComes...

Jims #94547-80A - Sprocket Shaft Bearing Race Tool

Sprocket Shaft Bearing Race ToolFeaturesMust use with JIMS® Race and Bearing Install Handle (PART# DS-196042)Used to remove and install Timken® bearing race on motor casesMade in the U.S.A...

Jims 97273-60 - Camshaft Bearing Tool - XL

Inner Cam Bearing Install Tool Use to install inner cam bearings Made in the U.S.A.

Jims #96385-78A - Shift Fork Gauge - 4-Speed - Big Twin

Shift Fork Gauge - 4-Speed - Big TwinFeaturesThis tool checks alignment of Big Twin transmission shift forksMade in the U.S.A.SpecsUnitsEachColor/FinishRedTypeFork AlignmentApplicationPlate-Type...

Jims #1743 - Swingarm Bushing Tool

Swingarm Bushing ToolFeaturesAllows installation of delicate, silicone cleveblock bushings in swingarm without damageTool presses on outer sleeve of bushingCan be used with or without a...

Jims #95960-52C - Clutch Hub Puller - '36-'90 Big Twin

Clutch Hub Puller - '36-'90 Big TwinFeaturesUsed to remove wet and dry clutch hubs without removing clutch release rod4 bolts included for dry clutch removalMade in the U.S.A.SpecsApplicationClutch...

Jims 1041-TC - Camshaft Cover Holder Tool - '70-'99 Big Twin

Cam Cover Holding Tool Holds cam cover flat and helps prevent damage/scratches when removing and installing bushings Clamps in vice or Bridgeport™ mill Made in the U.S.A.

Jims #96780-58A - Piston Pin Lock Ring Tool - Big Twin

Piston Pin Lock Ring Tool - Big TwinFeaturesUse to install lock ring (Harley-Davidson® No. 22582-52) in piston having .515” inner diameter wrist pins, like most aftermarket pistonsThis tool will...

Jims #94660-37A - Sprocket Locknut Wrench - Counter Shaft

Sprocket Locknut Wrench - Counter ShaftFeaturesRemoves hex nut from end of main drive gear that secures the rear drive transmission pulleyExtra-long two-piece designMade in the USAInner collar will...

Jims #1707 - Cleveblock Spreading Tool

Cleveblock Spreading ToolFeaturesSpreads the swing arm cleveblocs allowing for installation of the swing armUse to install the swing arm in a 5-Speed rubber mount frameComes with instructionsMade in...

Jims #94555-55A - Pinion Nut Socket - Big Twin

Pinion Nut Socket - Big TwinFeaturesUse to remove or secure pinion gear nut to pinion gear shaftMade in the U.S.A.SpecsProduct NameNutStyleSocketApplicationPinion GearDrive Size1/2"Riding...

Jims #94557-55A - Compensating Sprocket Socket Head - '55-'70

Compensating Sprocket Socket Head - '55-'70FeaturesUsed to remove and install compensating nutMade in the U.S.A.SpecsDrive Size1/2"Product NameSocketApplicationCompensating SprocketRiding...

Jims #95760-TP - Pinion Bearing Puller - Big Twin

Pinion Bearing Puller - Big TwinFeaturesUse to remove pinion bushing from cam cover in one easy operationUse with JIMS® Cam Cover HolderMade in the U.S.A.SpecsApplicationPinionProduct...

Jims #1010 - Rod Alignment Tool - Evolution

Rod Alignment Tool - EvolutionFeaturesUse to check rod straightness without removing the rods from the casesMade in the U.S.A.SpecsRiding StyleStreetStyleRodOverall Length4-1/2"ApplicationEngine...

Jims #1051 - Wrist Pin Bushing Tool

Wrist Pin Bushing ToolFeaturesUsed to remove and install wrist pin bushings without removing connecting rods from crankcasesComes with instructionsMade in the U.S.A.SpecsApplicationWrist...

Jims #1012-70TB - Cam Bushing Installer

Cam Bushing InstallerFeaturesUse to install bushing and drill dowel pin hole to factory specification#31 jobber length HSS drill bit included with jigsUse staking dowel pinMade in the U.S.A...

Jims #97225-55 - Sprocket Shift Bearing Installation Tool

Sprocket Shift Bearing Installation ToolFeaturesUsed on '84-'02 Big Twin to install the flywheel assembly to the left crankcase Timken® bearingMade in the U.S.A.SpecsRiding...

Jims #1006T - Motor Stand - Black - Evolution/Big Twin

Motor Stand - Black - Evolution/Big TwinFeaturesMakes working on motors easier with better accessMade in the USASpecsColor/FinishPowder-CoatedFeaturesFor Big Twin ModelsMaterialSteelRiding...