Jims

Jims 34734-80 - Main Drive Gear Bearing/Seal Installer Tool - 5-Speed

Main Drive Gear Bearing/Seal Installation Tool Holds bearings and seal square to its bore, eliminating any marring Install both bearings and seal with use of a one-ton press Install bearings and...

Jims 97081-54 - Sprocket Shaft Bearing Press Tool

Sprocket Shaft Bearing Installation Tool Use on '55-'76 XL and K models to install the flywheel assembly into the left crankcase Timken® bearing Optional sleeves sold separately for use on '86-'03...

Jims 1276 - Pin Remover - Wrist

Wrist Pin Tool Can be used easily by one person, no need to get another technician to hold the piston while drifting the pin in or out This new JIMS® tool will cut the time it takes to remove and...

Jims 34623-83 - Piston Pin Tool - Evolution

Piston Pin Keeper Tool This tool will install “Round Circlip” rings in one easy step without distorting ring, for the safest wrist pin retention possible Use to install retaining ring in piston ...

Jims 2232 - Bearing Race Tool

Steering Head Bearing Race Tool Removes and installs steering head bearing race on 84-16 Big Twin (except 14-16 Dressers), 86-16 XL and 94-02 Buell OEM frames (will also work on most aftermarket...

Jims 33096-54B - Kickstarter Shaft

Kickstarter Shaft Precision-machined replacement shaft Made in the U.S.A.

Jims 96600-36B - Valve Spring Compressor Tool - Harley-Davidson®

Valve Spring Compressor Tool Comes with new valve collar receiver for safer tool usage, and can be clamped in vice Hardened ball bearing style tip at valve head end eliminates damage to valve This...

Jims 1022 - Motor Stand - Blue - '99-'17 Twin Cam

Motor Stand Makes working on motors easier with better access Made in the USA

Jims 2388 - Driver Spacer Tool

Driver Spacer Tool Used with JIMS Bearing Race Tool to remove and install the steering head bearing race

Jims 33096-54AL - Kickstarter Shaft - 4-Speed Big Twin

Kickstarter Shaft Precision-machined replacement shaft Made in the U.S.A.

Jims 35125-37 - Mainshaft Bearing Race - 4-Speed Big Twin

Transmission Bearing Sold individually, unless noted.

Jims 23909-80 - Sprocket Shaft - Big Twin

Motor Sprocket Shaft Made in the U.S.A.

Jims 1800 - Hydrosolid Tappet

Hydrosolid Tappets Perform like a hydraulic tappet up to 5500 rpm, then turn into a solid tappet When they turn into solid tappets, it adds approximately three to six more usable horsepower ...

Jims 2474-1 - Tappet - Standard Solid - Big Twin

Powerglide™ Tappets These tappets will run in cast iron or aluminum tappet blocks Recommend fitting the tappets to the blocks with a clearance of .0007" to .0012" Produced from billet bearing...

Jims 24006-80/83 - Pinion Gear Shaft - Big Twin

Pinion Gear Shaft Made in the U.S.A.

Jims 2475-1 - Standard Solid Tappet - Big Twin

Powerglide™ Tappets These tappets will run in cast iron or aluminum tappet blocks Recommend fitting the tappets to the blocks with a clearance of .0007" to .0012" Produced from billet bearing...

Jims 2476-1 - Tappet - Standard Solid - Big Twin

Powerglide™ Tappets These tappets will run in cast iron or aluminum tappet blocks Recommend fitting the tappets to the blocks with a clearance of .0007" to .0012" Produced from billet bearing...

Jims 34186-76 - Shift Fork Shaft

Shift Fork Shaft — Shift Fork Shaft Kit Made in the U.S.A.

Jims 2464-1 - Standard Hydraulic Tappet - Big Twin

Powerglide™ Tappets These tappets will run in cast iron or aluminum tappet blocks Recommend fitting the tappets to the blocks with a clearance of .0007" to .0012" Produced from billet bearing...

Jims 24703-54B - Pinion Spacer

Pinion Gear Spacer Made in the U.S.A.

Jims 2461-1 - Hydraulic Tappet - Big Twin

Powerglide™ Tappets These tappets will run in cast iron or aluminum tappet blocks Recommend fitting the tappets to the blocks with a clearance of .0007" to .0012" Produced from billet bearing...

Jims 40520-63 - Shifter Shaft Bushings

Shifter Shaft Bushings American-made, high-quality replacements Sold in pack of 2 Made in the USA

Jims 25582-54/73 - Pinion Shaft Bushing

Pinion Shaft Bushing Quality pinion shaft bushings Made in the U.S.A.

Jims 2463-1 - Standard Hydraulic Tappet - Big Twin

Powerglide™ Tappets These tappets will run in cast iron or aluminum tappet blocks Recommend fitting the tappets to the blocks with a clearance of .0007" to .0012" Produced from billet bearing...