Jims

Jims #2392 - Head Bolt - Torque Plate

Head Bolt - Torque PlateFeaturesThis accurate gauge allows the measuring of 90° when tightening head boltsTorquing sequence laser engraved on gauge, with instructionsWorks on all Twin Cam and...

Jims #1726-1 - Bushing Reamer - Wrist Pin

Bushing Reamer - Wrist PinFeaturesSome wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications).Used to ream wrist pin bushings to the...

Jims #2043 - Fork Nut Socket - 41 mm

Fork Nut Socket - 41 mmFeaturesEliminates possible burring of plug caused by wrenchesUsed to remove and install top fork-tube plugFits 41 mm forksMade in the U.S.A.SpecsColor/FinishBlackProduct...

Jims #33334-79 - Transmission Sprocket Spacer - '80-E'84 Harley-Davidson

Transmission Sprocket Spacer - '80-E'84 Harley-DavidsonFeaturesSmooth finish for a longer seal life1.7" IDMade in the USASpecsLength0.687"TypeTransmissionTransmission Type5-SpeedProduct...

Jims #2316 - Primary Locking Bar - 4-Speed/5-Speed

Primary Locking Bar - 4-Speed/5-SpeedFeaturesImmobilizes primary driveAllows for tightening with a torque wrench or loosening with a breaker barPrevents damage to rotor or magnets sometimes caused by...

Jims #24335-36 - Wrist Pin Bushing - Big Twin

Wrist Pin Bushing - Big TwinFeaturesMachined from solid bronze bar stockHold concentricity to less than .0002"Lead-in edge for easy installationMade in the U.S.A.SpecsRiding...

Jims #95760-57 - Bushing Bearing Puller

Bushing Bearing PullerFeaturesUsed to remove rocker bushing or bearing in one easy operationMade in the U.S.A.SpecsRiding StyleStreetUnitsEachProduct NameBearing PullerApplicationRocker...

Jims #1705 - Exhaust Drill Plate

Exhaust Drill PlateFeaturesWill position the seal evenly into the exhaust port of headTool can be used with exhaust flange nutsMade in the U.S.A.SpecsColor/FinishBlueProduct NameSeal...

Jims #1053 - Oil Pump Seal Installer

Oil Pump Seal InstallerFeaturesFor use on all Big Twin aluminum oil pumps (except Twin Cam/M8)Easily installs oil pump seal below gear surface for a no-leak fitMade in the U.S.A...

Jims #1726-3 - Bushing Reamer - Wrist Pin

Bushing Reamer - Wrist PinFeaturesSome wrist pin bushings will require a small amount of ball honing to give specified fit (see H-D manual for specifications).Used to ream wrist pin bushings to the...

Jims #33344-94 - Transmission Sprocket Spacer - L'94-'06 Harley-Davidson

Transmission Sprocket Spacer - L'94-'06 Harley-DavidsonFeaturesSmooth finish for a longer seal life1.7" IDMade in the USASpecsLength0.600"Product NameSpacerTransmission...

Jims #25581-36 - Cam Bushing - Big Twin

Cam Bushing - Big TwinFeaturesBushing is made from solid bronze bar stockMachined in one operation with a tolerance of .0002"Features a lead-in for ease of installationMade in the U.S.A...

Jims #1700 - Main/Shaft Clutch Gear Tool

Main/Shaft Clutch Gear ToolFeaturesRemoves kick starter clutch gear successfully, without damage to the gearMade in the U.S.A.SpecsFor Engine Type4-SpeedRiding...

Jims #1725 - Head Bearing Race Installer

Head Bearing Race InstallerFeaturesUse to install steering head races, stock and custom, as well as install cups in the frameThis tool pulls the races and cups in, straight and true, without any...

Jims #2201K - Staking Dowel Pins - 10 Pack

Staking Dowel Pins - 10 PackFeaturesHolds bushing in placeMade in the USASpecsProduct NameDowel PinTypeStakingRiding StyleStreetUnits10 PackColor/FinishSilver

Jims #8998K - Transmission Door Bearings - '80-'03 Harley-Davidson

Transmission Door Bearings - '80-'03 Harley-DavidsonFeaturesMade in the USASpecsRiding StyleStreetUnitsPairProduct NameBearingTransmission Type5-SpeedTypeTransmission Door

Jims #2243 - Camshaft Seal Remover and Installer

Camshaft Seal Remover and InstallerFeaturesVery simple tool, just mount tool in cover, screw in the two removing screws, turn center, and out comes the cam sealThe new seal is then pressed in with...

Jims #33443-84 - Tappet Aligning Tool - Big Twin

Tappet Aligning Tool - Big TwinFeaturesCan also be used to align rocker box bases on Evolution head (requires two tools)Also used in Harley-Davidson® Twin Cam oil pump alignment applicationsUsed to...

Jims #1163 - Ball Shaft Retention Pins

Ball Shaft Retention PinsFeaturesLock into balancer shaft sprocket pinholes to prevent balancer from turning out of sync with flywheelUse to secure balancers when servicing the flywheel assemblyMade...

Jims #1111 - Camshaft Pinion Gauge Pins 108

Camshaft Pinion Gauge Pins 108FeaturesUse to check pinion gear for pitch diametersCheck service manual for sizing chartMade in the U.S.A.SpecsGauge0.108"Measurement SystemSAETypePinion Gear...

Jims #1167 - Bearing Tool - Balancer Shaft/Removal - '00-'06 Softail

Bearing Tool - Balancer Shaft/Removal - '00-'06 SoftailFeaturesInstalling portion is designed to push on the outer diameter of bearings preventing any damage to the bearing or it's borePulls the...

Jims #1148 - Rod Alignment Tool - Twin Cam

Rod Alignment Tool - Twin CamFeaturesUse to check rod straightness without removing the rods from the casesMade in the U.S.A.SpecsOutside Diameter0.927"Riding StyleStreetOverall...

Jims #25586-37 - Cam Bushing - XL

Cam Bushing - XLFeaturesBushings are made from solid bronze bar stockMachined in one operation with a tolerance of .0002"Feature a lead-in for ease of installationMade in the U.S.A.SpecsTypeCam...

Jims #2244 - Fork Nut Socket - 35 mm - 3/8"

Fork Nut Socket - 35 mm - 3/8"FeaturesUsed to remove and install top fork nuts on fork tubesRubber protector inside socketWill clear most handlebarsMade in the U.S.A.SpecsTypeRemoval ToolFork...